Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Get this product to enhance the one you read around.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Building and construction
Protected with blue rubber seals

CONSISTS OF:
Two Ball Bearings

NEEDS:
Assembly to automobile

SPECIFICATIONS:
Inner Size: 10mm
Outer Size: 15mm
Side Density: 4mm

COMMENTS:
These bearings are used to support the Primary Clutch (one needed).

Frequently gotten with the product that you are presently checking out.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Frequently gotten with the product that you are presently checking out.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

This is a fantastic enhancement to the product presently being reviewed.

Fr Bearing Carriers Rstlr/Stmpd/Nitro Slash

These are Optional Front Bearing Providers for the Traxxas Electric
Rustler, Stampede and Bandit

The Front axles fit into these bearing carriers.

FEATURES:
Black nylon building

CONSISTS OF:
Two Front bearing (hub) carriers
Two RPM decals

NEEDS:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

This is a fantastic enhancement to the product presently being reviewed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on automobile

You will certainly love this item if you have the item earlier discussed.

30T Idler Gear Steel

This is the optional Steel Idler Equipment for numerous Traxxas Vehicles.

FEATURES:
Steel building

CONSISTS OF:
One steel 30T idler gear

NEEDS:
Setup on automobile

This product compliments the main item here.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive gear that fits numerous Traxxas
cars. .
Consists of: 1 gear only

You will certainly love this item if you have the item earlier discussed.

Re Bearing Carriers Rstlr/Stmpd/Slsh

These are Optional Back Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles fit into these bearing carriers.

FEATURES:
Black nylon building

CONSISTS OF:
Two rear bearing (hub) carriers
Two RPM decals

NEEDS:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at widest point: 15.4mm (0.61")

You will certainly love this item if you have the item earlier discussed.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Complete Planetary Equipment Differential With Steel Ring Equipment
for the Traxxas Bandit, Stampede and Rustler.

FEATURES:
Metal gear shafts
Metal and plastic primary differential

CONSISTS OF:
Main differential with steel ring gear
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

NEEDS:
Setup on the automobile

COMMENTS:
For primary differential w/ steel ring - TRAC6380
World gear shafts - TRAC6382
Silicon grease _- TRAC6037