Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this item to enhance the one you read about.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for usage on the Traxxas Revo.

FEATURES:
Steel Construction
Shielded with blue rubber seals

CONSISTS OF:
2 Ball Bearings

NEEDS:
Assembly to vehicle

SPECS:
Inner Diameter: 10mm
External Diameter: 15mm
Side Density: 4mm

COMMENTS:
These bearings are used to support the Primary Clutch (one needed).

Frequently acquired with the item that you are currently reviewing.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECS:
Size: 5x8mm
Density: 0.5mm

Frequently acquired with the item that you are currently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Diameter: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL variation of the Rustler
or Stampede.

This is a fantastic addition to the item currently being discussed.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Providers for the Traxxas Electric
Rustler, Stampede and Outlaw

The Front axles fit into these bearing carriers.

FEATURES:
Black nylon building and construction

CONSISTS OF:
2 Front bearing (hub) providers
2 RPM decals

NEEDS:
(4) 5x11mm bearings, if needed usage (2) DTXC1547.

This is a fantastic addition to the item currently being discussed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

NEEDS:
Setup on vehicle

You will enjoy this product if you have the product earlier pointed out.

30T Idler Gear Steel

This is the optional Steel Idler Gear for lots of Traxxas Vehicles.

FEATURES:
Steel building and construction

CONSISTS OF:
One steel 30T idler equipment

NEEDS:
Setup on vehicle

This item praises the main item here.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel leading drive equipment that fits a number of Traxxas
cars. .
Includes: 1 equipment only

You will enjoy this product if you have the product earlier pointed out.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Back Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles fit into these bearing carriers.

FEATURES:
Black nylon building and construction

CONSISTS OF:
2 rear bearing (hub) providers
2 RPM decals

NEEDS:
(4) 5x11mm bearings, if needed usage (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at largest point: 15.4mm (0.61")

You will enjoy this product if you have the product earlier pointed out.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Gear Differential With Steel Ring Gear
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic main differential

CONSISTS OF:
Main differential with steel ring equipment
Planetary gears and shafts
Sun gears and shafts
Silicone grease

NEEDS:
Setup on the vehicle

COMMENTS:
For main differential w/ steel ring - TRAC6380
Planet equipment shafts - TRAC6382
Silicon grease _- TRAC6037