Traxxas 5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Get this product to boost the one you are reading about.

10 X 15 X 4Mm Ball Bearing (2) Blue Rubber Sheild Revo

This is a set of 10x15mm Ball Bearings for use on the Traxxas Revo.

FEATURES:
Steel Construction
Protected with blue rubber seals

CONSISTS OF:
2 Ball Bearings

REQUIRES:
Assembly to car

SPECIFICATIONS:
Inner Size: 10mm
Outer Size: 15mm
Side Thickness: 4mm

REMARKS:
These bearings are utilized to support the Main Clutch (one needed).

Frequently bought with the product that you are presently reviewing.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Thickness: 0.5mm

Frequently bought with the product that you are presently reviewing.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

This is a great addition to the product presently being discussed.

Front Bearing Carriers, For Slash 2Wd, Nitro Slash, E-Rustler &

These are Optional Front Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Outlaw

The Front axles fit into these bearing carriers.

FEATURES:
Black nylon construction

CONSISTS OF:
2 Front bearing (hub) providers
2 RPM decals

REQUIRES:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

This is a great addition to the product presently being discussed.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Strong Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on car

You will certainly enjoy this product if you have the product just above mentioned.

30T Idler Gear Steel

This is the optional Steel Idler Gear for numerous Traxxas Vehicles.

FEATURES:
Steel construction

CONSISTS OF:
One steel 30T idler equipment

REQUIRES:
Setup on car

This product compliments the main item below.

Steel Top Drive Gear 22T

This is the 22 tooth, solidified steel top drive equipment that fits a number of Traxxas
automobiles. .
Includes: 1 equipment just

You will certainly enjoy this product if you have the product just above mentioned.

Rear Bearing Carriers, For Traxxas Slash 2Wd, E-Rustler, E-Stamp

These are Optional Rear Bearing Carriers for the Traxxas Electric
Rustler, Stampede and Bandit.
The rear axles fit into these bearing carriers.

FEATURES:
Black nylon construction

CONSISTS OF:
2 rear bearing (hub) providers
2 RPM decals

REQUIRES:
(4) 5x11mm bearings, if needed use (2) DTXC1547.

SPECS:
Height: 40mm (1.58")
Width at widest point: 15.4mm (0.61")

You will certainly enjoy this product if you have the product just above mentioned.

Planetary Gear Diff W/Steel Ring Gear Slash/Bandit /Stampe

This is the Total Planetary Gear Differential With Steel Ring Gear
for the Traxxas Outlaw, Stampede and Rustler.

FEATURES:
Metal equipment shafts
Metal and plastic main differential

CONSISTS OF:
Main differential with steel ring equipment
Planetary equipments and shafts
Sun equipments and shafts
Silicone grease

REQUIRES:
Setup on the car

REMARKS:
For main differential w/ steel ring - TRAC6380
Planet equipment shafts - TRAC6382
Silicon grease _- TRAC6037