Traxxas 17T Pinion Gear 32P

This is a 17 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached straight to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

INCLUDES:
One 17 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This gear is only one of two which are utilized on the E-Maxx dual motor
    set-up.

Regularly gotten with the product that you are presently checking out.

15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached straight to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

INCLUDES:
One 15 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This gear is only one of two which are utilized on the E-Maxx dual motor
    set-up.

Get this product to improve the one you read about.

19T Pinion Gear 32P

This is a 19 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached straight to the motor.

FEATURES:
Machined Steel
Designed for a 3mm shaft

INCLUDES:
One 19 tooth Pinion Gear
One 3 x 4mm Set Screw

NEEDS:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten up set screw.

COMMENTS:
This gear is only one of two which are utilized on the E-Maxx dual motor
    set-up.

Below is one more product that compliments the product being reviewed.

Drive Hub, Center, Rear (1)/ F

This is the Front and Back Center Drive Center Set for use on the
Traxxas Slash 4x4 Vehicles.

FEATURES:
Nylon and steel construction

INCLUDES:
One Front Center Drive Center
One Back Center Drive Center
One Screw Pin

NEEDS:
Setup in drive assembly

Many others have gotten this product in addition to the product that you are presently checking out.

3 X 15Mm Button Hex Screw (6)

This is a package of 6 3x15mm Traxxas Button Head Screws.

FEATURES:
Steel construction, Black in color
Utilized on the Traxxas Revo beast truck, can also be utilized in any
    application where a 3x15mm button head screw is needed

INCLUDES:
Six 3x15mm Traxxas Button Head Screws

NEEDS:
2mm hex head wrench, GPMR8011

SPECS:
Length: 15mm
Size: 3mm

This product is often gotten with the above discussed product.

Horn Bracket 4-40 3/32"

These are 3/32" EZ Adjust Horn Brackets for 4-40 Threads

FUNCTIONS:
Nylon construction

INCLUDES:
Four horn brackets

NEEDS:
A rod with 4-40 threads

Below is a wonderful product that several others have purchased the very same time.



This is the Sidewinder SCT ESC and 3800kV Motor Combination from Castle Creations.

FEATURES:
Perfect for 2WD or 4WD brief course racing or backyard slamming
Neu-Castle 4 pole 1410 1Y motor has 50% more torque than Castle's
    CM36 series
Sidewinder SCT has 40% higher power handling than previous
    Sidewinder 1/10 scale ESC
Castle Link compatible (Field Link Portable Developer Vehicle Card
    (CSEM6300) needed, not consisted of)
Proportional brake with reverse lockout
Water resistant*

INCLUDES:
Castle Creations Sidewinder SCT ESC, 4mm Bullet Motor Connectors and
    Neu-Castle 4 pole 1410 1Y Brushless Motor, Directions

NEEDS:
Battery connector of modeler's choice

SPECS:
ESC
Input Voltage: Maximum 2S LiPo
Brake: Proportional
Reversible: Yes, with lockout
Width: 1.48" (37.5mm)
Length: 1.93" (49mm)
Height: 1.18" (30mm)
Weight: 2.29oz (65g) without battery connector
    Motor:
Pole Count: 4
Stator Lamination Thickness: 0.0078" .2mm
Bearings: CNC rated Japanese bearings
Measurements: 1.4 x 2.1" (36 x 53mm)
Shaft Size: 1/8" (3.2mm)

REMARKS:
*Not planned for operation while submerged in liquid. If device is
    run in wet conditions, rinse with fresh water to eliminate dirt
    or corrosives, then fully dry unit.
Maximum advised car weight is 6.5lbs (2.95kg)