Traxxas 15T Pinion Gear 32P

This is a 15 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached directly to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

CONSISTS OF:
One 15 tooth Pinion Gear
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This gear is just one of 2 which are utilized on the E-Maxx dual motor
    set-up.

Several others have actually acquired this thing together with the thing that you are currently checking out.

17T Pinion Gear 32P

This is a 17 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached directly to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

CONSISTS OF:
One 17 tooth Pinion Gear
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This gear is just one of 2 which are utilized on the E-Maxx dual motor
    set-up.

Several others have actually acquired this thing together with the thing that you are currently checking out.

14T Pinion Gear 32P

This is a 14 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached directly to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

CONSISTS OF:
One 14 tooth Pinion Gear
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This gear is just one of 2 which are utilized on the E-Maxx dual motor
    set-up.

Get this thing to boost the one you are reading about.

16T Pinion Gear 32P

This is a 16 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached directly to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

CONSISTS OF:
One 16 tooth Pinion Gear
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This gear is just one of 2 which are utilized on the E-Maxx dual motor
    set-up.

This thing praises the above discussed thing.

18T Pinion Gear 32P

This is a 18 Tooth 32 Pitch Pinion Gear for the Traxxas E-Maxx Truck.
This is the gear which is attached directly to the motor.

FEATURES:
Machined Steel
Created for a 3mm shaft

CONSISTS OF:
One 18 tooth Pinion Gear
One 3 x 4mm Set Screw

REQUIRES:
Assembly onto an E-Maxx truck.
1.5mm hex wrench to tighten set screw.

COMMENTS:
This gear is just one of 2 which are utilized on the E-Maxx dual motor
    set-up.

You will certainly like this thing if you have the thing above discussed.

Slipper Clutch Complete Stampede 4X4

This is the Complete Slipper Clutch Set for the Slash 4X4 from Traxxas.

FEATURES:
Complete slipper clutch assembly
Pre-assembled

CONSISTS OF:
2 nuts
1 spring
1 metal plate
1 pin
3 pads
2 washers
54T spur gear

REQUIRES:
Setup in automobile