Traxxas 1/10 Nitro Sport SE 2.4 RTR

This is the Traxxas Nitro Sport Ready-to-Run 1/10 scale Stadium Race Truck
with the 2.4GHz Traxxas TQ Pistol Grip Radio
and On-Board Push Button EZ Start System.
This set is based on the Nitro Rustler.

**The included TQ 2.4GHz radio system works only with the**
**#6519 receiver and does NOT accept the Docking Base device.**

FEATURES:
(RTR) All set To Run with radio system installed
Traxxas TQ 2.4GHz radio with water resistant digital high-torque
    guiding servo, water resistant receiver box
T-6 flat aluminum chassis rear and black fiber composite front
Countersunk holes under the chassis
Fiber composite upper plate/front brace
4 composite oil-filled Ultra shocks with white powder coated springs
4-wheel independent suspension
Telescoping U-joint drive shafts
281 Magnum, 6 (5x11mm) ball bearing transmission with adjustable
    slipper clutch and planetary gear differential with steel internal
    gears
75cc fuel tank with flip-top lid and primer bulb
Adjustable turnbuckle tie-rods
Composite black tuned pipeline with pressure fitting
Disc brake (composite)
Fiberglass front hinge pin brace (tie bar)
5 color ProGraphix painted body with bolt-on wing
Twin Spoke 2.2" wheels
Alias double pin rear tires and ribbed fron tires with foam inserts
Single point steering
Black colored composite parts
Front and rear bumpers
Pre-installed servo saver on servo
Black composite cover for the receiver and receiver battery box
Servo reversing and trim on radio
Air filter (one phase, bell formed)
Ballon type receiver cover
2.5 ounce (75cc) fuel tank with rubber install cushions
Pre-painted polycarbonate body with rear spoiler
Press button EZ start system with battery and battery charger
powered by a 6-cell battery (not included) that heats glow plug
and starts the engine with an on-board motor.
2-shoe clutch system
TRX Pro.15 engine w/ round alum heatsink (non-anodized) head
    foam bell type air filter, ball bearings, brief crankshaft,
    ABC construction, easy adjust two needle carburetor,
    on-board electric motor start system and glow starter,
    starter, tuned pipeline, glow plug, metal throttle arm,
    aluminum piston with oil groove, transported beam conecting rod

SPECIFICATIONS:
Length: 17.27" (439mm)
Front track: 12-1/2" (318mm)
Rear track: 12-3/8" (314mm)
Weight: 62 ounces (without radio)
Height: 6" (152mm)
Wheelbase: 11.313" (287mm)
Wheel size: 2.2"
Fuel capability: 2.5 ounces (75cc)
Engine: TRX Pro.15
Gear ratio: Adjustable 8.43:1 to 12.64:1
Differential: Planetary gear type (not ball)
Brake: Disc
Chassis: Double-decked (aluminum and composite)
Stimulate gear: 70 black nylon tooth (32 pitch)
Clutch bell: 20 tooth black steel (32 pitch)
Castor block front 30 degrees

INCLUDES:
One TQ 2.4GHz pistol grip radio
One Nitro Sport assembled with TRX-Pro .15 and two glow plugs
One Pre-Painted ProGraphix Body and Spoiler
One Decal sheet
One EZ start module with battery and 110V battery charger
One Black plastic shock collars and pistons
One Antenna tube and cap
6 5x11mm ball bearings in transmission
Eight 5x11mm metal bushings for wheels
Two 5x10mm bearings for clutch
One Bonus receiver cover balloon
One Directions
One Window mask sheet
One fuel bottle

REQUIRES:
Eight "AA" batteries, four for transmitter, four for battery box
Fuel

COMMENTS:
For ball bearings use:
    8- 5x11mm for wheels (DTXC1549 10 pack)
    6- 5x11mm for transmission
    2- 5x10mm for clutch (DTXC1535 2 pack)
Optional ball differential TRAC4420 and slipper clutch TRAC9615

Offered in the following colors;
    Blue, TRAC14BB Red, TRAC14RR
    Black, TRAC14LL Silver, TRAC14SS

REPLACING EZ BEGINNER WITH BASIC RECOIL BEGINNER
    To convert the EZ-Starting system to a basic pull-starter,
    purchase TRAG4070 take out the 3 bolts on the EZ-Starter,
    and install recoil starter.