Tekno RC 5602 1/8 ET48.3 Competition Electric Truggy Kit

This is the Electric Powered, Radio Controlled, 1/8 Scale
4WD Competitors ET48.3 Truggy Set from Tekno RC.

New routing front spindles and spindle providers
New V2 hinge pin braces and inserts
    New securing spring sets down with recorded shock boots
New rear centers
Low profile wing install
Modified bumper for increased ground clearance
Brand-new split center differential install
New straight turnbuckle rod ends
New tapered aluminum front center driveshaft
New quickly adjustable droop screws
    Modified shock standoffs for much easier droop measurement
Updated setup sheet for improved handling

FEATURES:
Chassis: CNC machined difficult anodized aluminum 0.16" (4mm) thick
    enhanced narrow layout, adjustable brace system for great tuning
    chassis flex with front, center, and rear braces
Drive: 4 wheel CV driveshafts with recorded pins on all 4
    wheels
Differentials: Three fluid filled, with straight cut CNC machined
    hardened steel ring and pinion gears,
Motor Mount: Two-piece CNC machined, double securing gear mesh
    change, light-weight direct-to-diff install style, install
    accomodates truggy or long can motors approximately 78mm long, install usages
    basic MOD 1 pinion, Tekno RC Traktion Drive or Elektri-Clutch
Shocks: CNC machined difficult anodized aluminum bodies, 16mm bore, 4mm
    hardened steel polished shafts, 5.4" (137mm) long rear shocks,
    4.8" (122mm) long front shocks, truggy particular springs, CNC
    machined 8x1.3mm tapered pistons
Shock Towers: CNC machined anodized 7075 aluminum, front 0.24" (6mm)
    thick, rear 0.20" (5mm) thick, revised shock standoffs for much easier
    sag measurement
Suspension: Totally adjustable long travel geometry, truggy particular
    arms and sway bars, lightened aluminum pivot balls, adjustable
    anti-squat, rear arms, roll center, and bump steer
Body: Clear truggy type with high downforce wing, & low center of
    gravity light-weight wing install
Steering: Complete ball bearing geared up, lightened aluminum posts,
    adjustable bump steer and Ackerman, Ackerman explains the effect
    of the within front wheel turning faster than the outside front
    wheel during turns, adjustable stops, CNC machined aluminum
    Ackerman plate, adjustable steering picks up exact steering
    travel settings
Caster: Adjustable, caster/toe-in refers to the angle of the front
    suspension when viewed from the side of the automobile in relation to
    the chassis
Camber: Adjustable front and rear, camber refers to the angle of the
    tops of the tires from vertical when viewed from front or behind
    automobile

INCLUDES:
ET48.3 Truggy Set with Body, Decals, Shocks, Shock Oil, Diff Oil, and
    Directions

NEEDS:
Radio: 2-3 channel with high-torque steering servo, and optional
    brake servo
Motor: Brushless advised
ESC: Compatible with selected motor
Battery: 4-6S LiPo
Battery Battery charger: For selected battery
MOD 1 Pinion or Traktion Drive/Elektri-Clutch system
Tires and Wheels: 1/8 scale truggy type with inserts
Paint, building and track equipment

SPECIFICATIONS:
Automobile-
Length: 23.4" (595mm)
Wheelbase: 14.8-15.1"(375-385mm) adjustable
Weight: 9lbs (4000g) differs with equipment & battery used
Width: 16.4-16.5"* (416-420mm*) *optional centers needed
Dry Weight: 9.0pounds (4000g) might vary with equipment used
Diff Ratio: F/R 9/40t, center 44T
Battery Tray Dimensions: 1.9x5.8" (50x148mm) 2x2s or 1x4s config.
    Body-
Length: 17.5" (444mm)
Width: 4.8" (123mm)
Height: 5" (127mm)

COMMENTS:
For Replacement Ball Bearings use:
    Qty. Size Area Qty. Bearing Set
    2 8x16mm Center Diff 1 DTXC1585
    2 8x16mm Front Diff 1 DTXC1585
    2 8x16mm Rear Diff 1 DTXC1585
    2 5x11mm Front Gearbox 1 DTXC1547
    2 5x13mm Rear Gearbox 1 TKRC5015
    2 13x19mm Rear Hubs 1 TKRC3194
    2 8x16mm Rear Hubs 1 DTXC1585
    2 13x19mm Front Hubs 1 TKRC3194
    2 13x19mm Front Hubs 1 TKRC3194
    4 6x10mm Steering 2 DTXC1561