Tekno RC 5602 1/8 ET48.3 Competition Electric Truggy Kit

This is the Electric Powered, Radio Controlled, 1/8 Scale
4WD Competition ET48.3 Truggy Kit from Tekno RC.

New trailing front spindles and spindle carriers
New V2 hinge pin braces and inserts
    New clamping spring sets down with caught shock boots
New rear hubs
Low profile wing install
Modified bumper for increased ground clearance
Brand-new split center differential install
New straight turnbuckle rod ends
New tapered aluminum front center driveshaft
New easily adjustable droop screws
    Modified shock standoffs for simpler droop measurement
Updated setup sheet for enhanced handling

FUNCTIONS:
Chassis: CNC machined difficult anodized aluminum 0.16" (4mm) thick
    optimized narrow layout, adjustable brace system for great tuning
    chassis flex with front, center, and rear braces
Drive: Four wheel CV driveshafts with caught pins on all four
    wheels
Differentials: Three fluid filled, with straight cut CNC machined
    hardened steel ring and pinion gears,
Motor Mount: Two-piece CNC machined, double clamping equipment mesh
    adjustment, lightweight direct-to-diff install design, install
    accomodates truggy or long can motors approximately 78mm long, install uses
    standard MOD 1 pinion, Tekno RC Traktion Drive or Elektri-Clutch
Shocks: CNC machined difficult anodized aluminum bodies, 16mm bore, 4mm
    hardened steel polished shafts, 5.4" (137mm) long rear shocks,
    4.8" (122mm) long front shocks, truggy specific springs, CNC
    machined 8x1.3mm tapered pistons
Shock Towers: CNC machined anodized 7075 aluminum, front 0.24" (6mm)
    thick, rear 0.20" (5mm) thick, revised shock standoffs for simpler
    sag measurement
Suspension: Totally adjustable long travel geometry, truggy specific
    arms and sway bars, lightened aluminum pivot balls, adjustable
    anti-squat, rear arms, roll center, and bump guide
Body: Clear truggy type with high downforce wing, & low center of
    gravity lightweight wing install
Steering: Full ball bearing equipped, lightened aluminum posts,
    adjustable bump guide and Ackerman, Ackerman describes the impact
    of the within front wheel turning faster than the outdoors front
    wheel during turns, adjustable stops, CNC machined aluminum
    Ackerman plate, adjustable steering stops for precise steering
    travel settings
Caster: Adjustable, caster/toe-in refers to the angle of the front
    suspension when seen from the side of the vehicle in relation to
    the chassis
Camber: Adjustable front and back, camber refers to the angle of the
    tops of the tires from vertical when seen from front or behind
    car

CONSISTS OF:
ET48.3 Truggy Kit with Body, Decals, Shocks, Shock Oil, Diff Oil, and
    Directions

REQUIRES:
Radio: 2-3 channel with high-torque steering servo, and optional
    brake servo
Motor: Brushless suggested
ESC: Compatible with chosen motor
Battery: 4-6S LiPo
Battery Battery charger: For chosen battery
MOD 1 Pinion or Traktion Drive/Elektri-Clutch system
Tires and Wheels: 1/8 scale truggy type with inserts
Paint, building and track equipment

SPECS:
Car-
Length: 23.4" (595mm)
Wheelbase: 14.8-15.1"(375-385mm) adjustable
Weight: 9lbs (4000g) varies with equipment & battery used
Width: 16.4-16.5"* (416-420mm*) *optional hubs needed
Dry Weight: 9.0lbs (4000g) may vary with equipment used
Diff Ratio: F/R 9/40t, center 44T
Battery Tray Dimensions: 1.9x5.8" (50x148mm) 2x2s or 1x4s config.
    Body-
Length: 17.5" (444mm)
Width: 4.8" (123mm)
Height: 5" (127mm)

COMMENTS:
For Replacement Ball Bearings usage:
    Qty. Size Area Qty. Bearing Set
    2 8x16mm Center Diff 1 DTXC1585
    2 8x16mm Front Diff 1 DTXC1585
    2 8x16mm Rear Diff 1 DTXC1585
    2 5x11mm Front Transmission 1 DTXC1547
    2 5x13mm Rear Transmission 1 TKRC5015
    2 13x19mm Rear Hubs 1 TKRC3194
    2 8x16mm Rear Hubs 1 DTXC1585
    2 13x19mm Front Hubs 1 TKRC3194
    2 13x19mm Front Hubs 1 TKRC3194
    4 6x10mm Steering 2 DTXC1561