Suppo Model 1400Kv Brushless Outrunner Motor, 3.17MM Shaft, 3.5MM Bullet Con

LI-Poly Cell:2-3
Ni-MH Cells: 6-10
RPM/V: 1250Kv
Max. efficiency existing: 6-12 Amp
NoLoad current / 0.7 Amp
Existing capability: 16 A/60 s
Max. Performance: 75%
Shaft size: 3mm
Weight with cable televisions: 47g
Measurements(mm): 27.5x30

Advised Design Weight: 300 - 800 g
Recommended Prop w/o Gearbox: 7 cells (2xLi) 9."x5; 8 cells 9x5; 10 cells 8.5x6; 3xLi 8x4

Many others have bought this thing in addition to the thing that you are currently checking out.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon construction decreases rotating mass for
    greater output and longer life.
Reinforcing carbon fibers help preserve true, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring guideline sheet

REQUIRES:
ALL props need balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 8"
Pitch: 3.8

REMARKS:
Slo-Flyer props are Not developed for Glow engines

Get this thing to improve the one you are reading about.

8x6EP Thin Electric Pusher Propeller

This is a 8x6EP Thin Composite Propeller from Advanced Precision Composites.
For use on electrical powered airplane just (not for radiance engines).

FUNCTIONS:
Gray composite construction
Includes five adapter rings that adapt to various motor shafts.

INCLUDES:
One 8x6EP Thin Electric Propeller

REQUIRES:
ALL props need balancing, this is VERY important, use TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Diameter: 8"
Pitch: 6
Center inner size: 0.25" (6.3mm)

This thing praises the above talked about thing.

Tower Pro SG90 Servo

Features:
Micro Servo Titan 9g servo
Equipment Type : All Nylon Equipment
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Specs:
Measurement : 23mm x 12mm x 29mm
Connector Wire Length : About 248mm
Running Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature level Range : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packing content:
1 x 9g TITAN Servo Sets (with devices)

You will love this product if you have the product previously discussed.

10x4.7 Slow Flyer Propeller

This is a 10x4.7 Slo-Flyer "tractor" (not a "pusher") airplane propeller.
This prop produces a great deal of torque even at low speeds.

FEATURES:
Computer-optimized design offers these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon construction decreases rotating mass for
    greater output and longer life.
Reinforcing carbon fibers help preserve true, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft locating rings
One locating ring guideline sheet

REQUIRES:
ALL props need balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECS:
Length: 10"
Pitch: 4.7

REMARKS:
Slo-Flyer props are Not developed for Glow engines