Suppo Model 1400Kv Brushless Outrunner Motor, 3.17MM Shaft, 3.5MM Bullet Con

LI-Poly Cell:2-3
Ni-MH Cells: 6-10
RPM/V: 1250Kv
Max. efficiency current: 6-12 Amp
NoLoad current / 0.7 Amp
Existing capacity: 16 A/60 s
Max. Performance: 75%
Shaft diameter: 3mm
Weight with cable televisions: 47g
Dimensions(mm): 27.5x30

Recommended Model Weight: 300 - 800 g
Recommended Prop w/o Gearbox: 7 cells (2xLi) 9."x5; 8 cells 9x5; 10 cells 8.5x6; 3xLi 8x4

Many others have purchased this thing along with the thing that you are presently reviewing.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon construction minimizes turning mass for
    higher output and longer life.
Reinforcing carbon fibers assist maintain true, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft finding rings
One finding ring instruction sheet

REQUIRES:
ALL props need balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not designed for Glow engines

Get this thing to enhance the one you are reading around.

8x6EP Thin Electric Pusher Propeller

This is a 8x6EP Thin Composite Propeller from Advanced Accuracy Composites.
For utilize on electric powered aircraft only (not for glow engines).

FUNCTIONS:
Gray composite construction
Comes with five adjuster rings that adapt to different motor shafts.

INCLUDES:
One 8x6EP Thin Electric Propeller

REQUIRES:
ALL props need balancing, this is ESSENTIAL, utilize TOPQ5700.
May requirement prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Diameter: 8"
Pitch: 6
Hub inner diameter: 0.25" (6.3mm)

This thing compliments the above talked about thing.

Tower Pro SG90 Servo

Features:
Micro Servo Titan 9g servo
Equipment Type : All Nylon Equipment
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Requirements:
Measurement : 23mm x 12mm x 29mm
Adapter Wire Length : About 248mm
Running Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature level Variety : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packaging content:
1 x 9g TITAN Servo Sets (with accessories)

You will like this thing if you have the thing above stated.

10x4.7 Slow Flyer Propeller

This is a 10x4.7 Slo-Flyer "tractor" (not a "pusher") aircraft propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design provides these props a thinner profile and
    more "bite" with less noise.
Lightweight molded nylon construction minimizes turning mass for
    higher output and longer life.
Reinforcing carbon fibers assist maintain true, constant pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of small shaft finding rings
One finding ring instruction sheet

REQUIRES:
ALL props need balancing (usage TOPQ5700)
May need prop reamer, usage GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 10"
Pitch: 4.7

COMMENTS:
Slo-Flyer props are Not designed for Glow engines