Suppo Model 1400Kv Brushless Outrunner Motor, 3.17MM Shaft, 3.5MM Bullet Con

LI-Poly Cell:2-3
Ni-MH Cells: 6-10
RPM/V: 1250Kv
Max. effectiveness present: 6-12 Amp
NoLoad current / 0.7 Amp
Present capacity: 16 A/60 s
Max. Performance: 75%
Shaft diameter: 3mm
Weight with cable televisions: 47g
Dimensions(mm): 27.5x30

Advised Design Weight: 300 - 800 g
Recommended Prop w/o Gearbox: 7 cells (2xLi) 9."x5; 8 cells 9x5; 10 cells 8.5x6; 3xLi 8x4

Many others have purchased this thing in addition to the thing that you are presently checking out.

8x3.8 Slow Flyer Propeller

This is a 8x3.8 Slo-Flyer "tractor" (not a "pusher") plane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon construction minimizes rotating mass for
    higher output and longer life.
Reinforcing carbon fibers assist preserve true, continuous pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft finding rings
One finding ring instruction sheet

NEEDS:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 8"
Pitch: 3.8

COMMENTS:
Slo-Flyer props are Not developed for Radiance engines

Get this thing to enhance the one you read about.

8x6EP Thin Electric Pusher Propeller

This is a 8x6EP Thin Composite Propeller from Advanced Precision Composites.
For use on electrical powered aircraft just (not for glow engines).

FEATURES:
Gray composite construction
Has five adjuster rings that adapt to different motor shafts.

INCLUDES:
One 8x6EP Thin Electric Propeller

NEEDS:
ALL props need balancing, this is ESSENTIAL, use TOPQ5700.
May requirement prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Size: 8"
Pitch: 6
Center inner diameter: 0.25" (6.3mm)

This thing praises the above gone over thing.

Tower Pro SG90 Servo

Functions:
Micro Servo Titan 9g servo
Equipment Type : All Nylon Equipment
Dead Band Width : 2 usec
Stall Torque : 1.5kg/cm at 4.8V
Operation Voltage : 3.0 - 7.2Volts

Specifications:
Dimension : 23mm x 12mm x 29mm
Port Wire Length : About 248mm
Operating Speed : 0.12sec / 60 degrees (4.8V no load)
Temperature Range : -30 to +60 Degree C
Net weight : about 11g
Color : black

Packaging content:
1 x 9g TITAN Servo Sets (with devices)

You will certainly like this thing if you have the thing just above discussed.

10x4.7 Slow Flyer Propeller

This is a 10x4.7 Slo-Flyer "tractor" (not a "pusher") plane propeller.
This prop produces a lot of torque even at low speeds.

FEATURES:
Computer-optimized design gives these props a thinner profile and
    more "bite" with less noise.
Lightweight formed nylon construction minimizes rotating mass for
    higher output and longer life.
Reinforcing carbon fibers assist preserve true, continuous pitch at
    any rpm.
Slo-Flyer propellers work well with Electric powered Park Flyer-type
    aircraft.

INCLUDES:
One carbon-reinforced nylon propeller
One set of little shaft finding rings
One finding ring instruction sheet

NEEDS:
ALL props need balancing (use TOPQ5700)
May need prop reamer, use GPMQ5005 (SAE) or GPMQ5007 (Metric)

SPECIFICATIONS:
Length: 10"
Pitch: 4.7

COMMENTS:
Slo-Flyer props are Not developed for Radiance engines