Savox Waterproof Standard Digital Servo 0.15Sec / 208Oz @ 6V

The SW0231MG is a budget plan friendly water resistant digital servo with fantastic torque for numerous applications. This brushed servo features a speed of .17 and 208.0 oz-in of torque 6.0V. It integrates leading edge technology with extremely high 12-bit (4096) resolution and metal equipments for your greater precision when dodging puddles. This is an excellent upgrade if your seeking to drive your RC car in any condition...rain, sleet, or snow.

Features:

• Combines leading edge
  technology with extremely high 12 bit (4096) resolution and metal gears.
• Waterproof.
• Brushed motor
• Extremely strong metal equipments make sure long-life and durability.
• Our servos are completely green ? from materials to production, these servos are ecologically friendly.
• Ideal for RC automobiles, trucks, buggies, and boats.

Dimensions(mm): 41.8x20.2x42.9
Weight(g): 66
Speed(@6.0V sec/60): .17
Torque(@6.0V oz-in): 208.0
Equipment: Metal
Bearing: 2BB
Case: Plastic
25 Tooth Spline
IP Score: 67
Frequency: 200-250hz
Pulse Width Frequency: 1520

This item is frequently purchased with the above mentioned item.

Aluminum Servo Horn 25T

This is the Axial 25T Aluminum Servo Horn for Futaba, Axial and Savox Servos.

FEATURES:
Difficult anodized aluminum building
Compression install, 2 screws set up on either side of arm and
    tighten up center hole around servo spline

CONSISTS OF:
Axial 25T Aluminum Servo Horn
2 2x8mm socket head screws

SPECIFICATIONS:
Length: 0.98" (25mm) from center of servo mounting hole to end of arm
Hole Diameter: 3mm
Pitch:3x30

This item is frequently purchased with the above mentioned item.



This is a optional Racers Edge Aluminum single arm servo horn, meant for use with Futaba servos. This sturdy aluminum servo horn is comparable in design to the Racers Edge Pro Adjustable servo horns, but features a third linkage mounting point and does not utilize lock down screws.

This item compliments the above gone over item.



This is the 3-Channel Futaba 3PRKA 2.4GHz FHSS Radio System
with the R203GF Receiver.

FEATURES:
Ideal upgrade for radios found in RTR cars
Throttle and guiding trim and reverse
Steering double rate dial
Throttle end point change
Channel three switch
Throttle fail safe
One year restricted service warranty through Hobby Solutions starting at date
    of purchase

CONSISTS OF:
Futaba 3PRKA 2.4GHz FHSS Transmitter, R203GF Receiver, Guideline
    Handbook and On/Off Switch

NEEDS:
Servos of modeler's option
4 AA batteries for transmitter

SPECIFICATIONS:
Transmitter:
Sending Frequency: 2.4GHz band
Power Requirement: 4 AA cells
Present Drain: 100mA or less

    Receiver;
Measurements: 1.54 x 1.02 x 0.39" (39 x 26 x 10mm)
Weight: 0.28oz (8g)
Operating Voltage: 4.8 - 7.4V (shown servo)
Battery Fail Safe Voltage: 3.8V*
Present Drain: 30mA at no signal
*Battery fail safe voltage is set for 4-cell NiCd/NiMH battery
Battery F/S does not work effectively when other kind of battery is utilized

COMMENTS:
2.4GHz FHSS is not compatible with FASST systems.
Normal mode frame rate is (FHSS/S-FHSS) 13.63ms and accepts any
kind of servos or peripherals.
High-Speed mode (in 4PL tx only), with an output of 6.8ms accepts
    digital servos consisting of the BLS series and most peripheral
    devices such as brushless ESCs