Savox Waterproof Standard Digital Servo 0.15Sec / 208Oz @ 6V

The SW0231MG is a budget plan friendly water resistant digital servo with great torque for many applications. This brushed servo functions a speed of .17 and 208.0 oz-in of torque 6.0V. It combines leading edge technology with extremely high 12-bit (4096) resolution and metal gears for your greater accuracy when dodging puddles. This is a fantastic upgrade if your aiming to drive your RC vehicle in any condition...rain, sleet, or snow.

Functions:

• Combines cutting edge
  technology with extremely high 12 bit (4096) resolution and metal gears.
• Waterproof.
• Brushed motor
• Exceptionally strong metal gears ensure long-life and durability.
• Our servos are totally green ? from materials to production, these servos are environmentally friendly.
• Ideal for RC vehicles, trucks, buggies, and boats.

Dimensions(mm): 41.8x20.2x42.9
Weight(g): 66
Speed(@6.0V sec/60): .17
Torque(@6.0V oz-in): 208.0
Equipment: Metal
Bearing: 2BB
Case: Plastic
25 Tooth Spline
IP Rating: 67
Frequency: 200-250hz
Pulse Width Frequency: 1520

This thing is frequently purchased with the above discussed thing.

Aluminum Servo Horn 25T

This is the Axial 25T Aluminum Servo Horn for Futaba, Axial and Savox Servos.

FEATURES:
Difficult anodized aluminum building
Compression install, 2 screws set up on either side of arm and
    tighten center hole around servo spline

CONSISTS OF:
Axial 25T Aluminum Servo Horn
2 2x8mm socket head screws

SPECIFICATIONS:
Length: 0.98" (25mm) from center of servo installing hole to end of arm
Hole Diameter: 3mm
Pitch:3x30

This thing is frequently purchased with the above discussed thing.



This is a optional Racers Edge Aluminum single arm servo horn, planned for use with Futaba servos. This strong aluminum servo horn is comparable in design to the Racers Edge Pro Adjustable servo horns, but includes a third linkage installing point and does not use lock down screws.

This thing compliments the above gone over thing.



This is the 3-Channel Futaba 3PRKA 2.4GHz FHSS Radio System
with the R203GF Receiver.

FEATURES:
Suitable upgrade for radios found in RTR cars
Throttle and steering trim and reverse
Steering dual rate dial
Throttle end point modification
Channel 3 switch
Throttle fail safe
One year restricted service warranty through Hobby Services starting at date
    of purchase

CONSISTS OF:
Futaba 3PRKA 2.4GHz FHSS Transmitter, R203GF Receiver, Instruction
    Handbook and On/Off Change

NEEDS:
Servos of modeler's choice
4 AA batteries for transmitter

SPECIFICATIONS:
Transmitter:
Sending Frequency: 2.4GHz band
Power Requirement: 4 AA cells
Current Drain: 100mA or less

    Receiver;
Measurements: 1.54 x 1.02 x 0.39" (39 x 26 x 10mm)
Weight: 0.28oz (8g)
Operating Voltage: 4.8 - 7.4V (shared with servo)
Battery Fail Safe Voltage: 3.8V*
Current Drain: 30mA at no signal
*Battery fail safe voltage is set for 4-cell NiCd/NiMH battery
Battery F/S does not work correctly when other type of battery is used

COMMENTS:
2.4GHz FHSS is not compatible with FASST systems.
Normal mode frame rate is (FHSS/S-FHSS) 13.63ms and accepts any
type of servos or peripherals.
High-Speed mode (in 4PL tx just), with an output of 6.8ms accepts
    digital servos including the BLS series and most peripheral
    equipment such as brushless ESCs