RPM Rear Bearing Carrier For Traxxas Slash 4X4 Or Rustler 4X4, Black

These are optional Back Bearing Carriers for the Traxxas Slash 4x4, Nitro
Rustler, Nitro Stampede, Nitro Sport, Rad2, Hawk 2 and Eagle/Eagle LSII.

FEATURES:
Nylon building and construction
Black in color

CONSISTS OF:
2 Back Bearing Carriers
Decal

REQUIRES:
2 5x11x4mm ball bearings, DTXC1547

Here is another item that praises the item being talked about.

Front Or Rear A-Arms For Traxxas Slash 4X4 And Rustler 4X4, Blac

These are the optional RPM Sturdy Front/Rear A-Arms
for the Traxxas Slash 4x4.

FEATURES:
Black in color
Plastic constrution

CONSISTS OF:
2 Front/Rear A-Arms

REQUIRES:
Setup at front or rear suspension

SPECS:
Length: 3.96" (100.5mm)
Width: 1.79" (45.5mm) at largest point
Thickness: 0.31" (8mm)

COMMENTS:
Likewise available in Blue (RPMC0705)

Here is a excellent item that several others have bought at the very same time.

Caster Blocks & Spindle Blocks For The Slash 4X4, Stampede 4X4,

These are the optional RPM Caster and Steering Blocks for all versions of the
Traxxas Slash 4x4, Stampede 4x4 and the 1/10 scale Rally 4WD.

FEATURES:
Plastic building and construction

CONSISTS OF:
2 Caster Blocks and 2 Guiding Blocks

You will like this thing if you have the thing earlier mentioned.

Led Lightbar Chrome (4) Clear Lights

This is the Clear LED Lightbar in Chrome
for the Traxxas Stampede 4x4 VXL, TRAD29**.

FEATURES:
Four clear LED lights in chrome surface plastic housings

CONSISTS OF:
Four Lights with Housings, Wiring, Mounting Hardware and Instructions

SPECS:
Real estate Size: 0.68" (17.3mm)

This item praises the above talked about item.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

CONSISTS OF:
Front driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

Here is a excellent item that several others have bought at the very same time.

Drive Shaft Assembly Rear Heavy Duty Stampede 4X4

This is the Sturdy Driveshaft Assembly for the Slash 4x4 from Traxxas

FEATURES:
Black plastic and steel building and construction

CONSISTS OF:
Rear driveshaft assembly
Screw pin

REQUIRES:
Setup on automobile

Lots of others have purchased this item along with the item that you are presently reading about.

Shock Rebuild Big Bore/Ultra

This is a shock rebuild kit for 2 Traxxas black plastic shocks. Includes:

4 E-clips
2 C-clips
2 O-rings
8 Washers
2 Diaphrams

This is a amazing enhancement to the item presently being talked about.

Spring Retainers

These are the Traxxas Spring Retainers for Traxxas Shocks.
This set includes the spring retainers that hold the springs in
place over the shock body and the piston heads that control the quantity
of oil flow in the shock cylinder.

FEATURES:
Constructed of molded plastic.
Contains enough parts for 2 shocks.
Fits the shocks on the majority of Traxxas nitro and electric powered vehicles.
Two hole piston moving towards greater dampening or three hole piston head
    for softer spring performance.

INCLUDES:
One Traxxas Spring Retainer Set with:
    2 upper and 2 lower spring retainers
    2 2 hole piston head covers
    Two 3 hole piston head covers

REQUIRES:
Disassembly of shock to install parts.

The below item likewise pairs actually well with the item being talked about.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)