RPM Black Gearbox Housing And Rear Mounts For Traxxas 2Wd Vehicles

This is the optional RPM Hybrid Gearbox Housing in Black
for the Traxxas 1/10 scale 2WD Slash, Stampede, E-Rustler and Bandit.

FEATURES:
0.12" (3mm) thick 6061 T6 aluminum motor plate provides strength to
    lock in gear mesh, and better heat dissipation than stock plastic
    motor plate
Motor plate is different from rear bumper mounts eliminating damage to
    the plate in case of a rear collision
Formed nylon gearbox housing with stock bumper installing holes
Different housing and rear mounts permit transmission maintenance
    without affecting suspension settings
0° and 3° formed rear mounts offer tighter tolerances and less slop
    than machined components for better camber and toe angle retention

INCLUDES:
2 Gearbox Real estates, Motor Plate, two 0° and two 3° Rear Mounts and
    Instructions

This product praises the above discussed product.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This product praises the above discussed product.

Steel Top Drive Gear 22T

This is the 22 tooth, hardened steel leading drive gear that fits numerous Traxxas
cars. .
Consists of: 1 gear only

Right here is another product that praises the product being discussed.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

INCLUDES:
One slipper clutch set

SPECS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

COMMENTS:
This part will fit both the requirement and XL version of the Rustler
or Stampede.

You will love this product if you have the product earlier discussed.

Alum Slipper Pressure Plate & Hub Jato

These are the Slipper Press Plate and Center
for the Traxxas Nitro Jato Stadium Truck.

FEATURES:
Pot Metal Construction
Silver in Color

INCLUDES:
One Slipper Press Plate
One Slipper Press Plate Center

NEEDS:
Assembly onto Car

Many others have purchased this product along with the product that you are currently checking out.

Spur Gear (90T) 48P

This is a Traxxas 48P, 90T Spur Gear for designs
with Torque Control Slipper Clutch.

FEATURES:
48 pitch
90 tooth
Designed for designs with a slipper clutch
Black plastic building and construction

INCLUDES:
One spur gear

SPECS:
Pitch: 48
Tooth: 90

COMMENTS:
For this slipper clutch design there is also a 76T gear (TRAC4676),
    83T gear (TRAC4683) and 86T gear (TRAC4686).

Many others have purchased this product along with the product that you are currently checking out.

Wheelie Bar Assem Stamp/Rust/Bandit

This is an optional Wheelie Bar for the Traxxas
Electric Stampede, Rustler and Bandit.

FEATURES:
Constructed of hardened plastic, black in color
Installs at back of chassis to prevent car from turning over
    throughout wheelies

INCLUDES:
Assembled optional Wheelie Bar with installing instructions and
    hardware

NEEDS:
Fastening to back of chassis

The listed below product likewise pairs really well with the product being discussed.

30T Idler Gear Steel

This is the optional Steel Idler Gear for many Traxxas Vehicles.

FEATURES:
Steel building and construction

INCLUDES:
One steel 30T idler gear

NEEDS:
Installation on car