RPM Caster Blocks & Spindle Blocks For The Slash 4X4, Stampede 4X4,

These are the optional RPM Caster and Steering Blocks for all versions of the
Traxxas Slash 4x4, Stampede 4x4 and the 1/10 scale Rally 4WD.

FUNCTIONS:
Plastic building

INCLUDES:
Two Caster Blocks and two Steering Blocks

Several others have gotten this item in addition to the item that you are presently checking out.

Rear Bearing Carrier For Traxxas Slash 4X4 Or Rustler 4X4, Black

These are optional Back Bearing Carriers for the Traxxas Slash 4x4, Nitro
Rustler, Nitro Stampede, Nitro Sport, Rad2, Hawk 2 and Eagle/Eagle LSII.

FEATURES:
Nylon building
Black in color

INCLUDES:
Two Back Bearing Carriers
Decal

REQUIRES:
Two 5x11x4mm ball bearings, DTXC1547

Several others have gotten this item in addition to the item that you are presently checking out.

Front Or Rear A-Arms For Traxxas Slash 4X4 Or Rustler 4X4, Red

These are the optional RPM Heavy Duty Front or Rear A-Arms in Red
for the Traxxas Slash 4x4, and Stampede 4x4.

FUNCTIONS:
Each A-arm is 0.22oz (6.5g) lighter than stock A-arm
Gets rid of slop in suspension and tightens up tolerances around hinge
    pins
Decreased fore and aft motion at inner hinge pin and axle carriers
    by higher than 90%
Nylon mix building, red in color

INCLUDES:
Left and Right Front or Rear A-Arms (two plans needed to
    total one truck

This is a wonderful addition to the item presently being discussed.

Slipper Pressure Plate & Hub Revo

This is a Replacement Slipper Pressure Plate and Slipper Hub for the Revo.
These are part of the slipper assembly.

FEATURES:
Aluminum building

INCLUDES:
One slipper pressure plate
One slipper center

REQUIRES:
Installation onto automobile.

Right here is an additional item that compliments the item being discussed.

Rebuild Kit Hd Slipper Clutch

This is the Heavy Duty Slipper Clutch Rebuild Kit from Traxxas.

FEATURES:
Parts for both nitro and electric Revo and Maxx trucks

INCLUDES:
3 Pads, steel Slipper Disc, two Locknuts, 2x9.8mm Pin, two
    Locknuts, Spring, two Spring Washers and Recommendations

REQUIRES:
Disassembly of slipper clutch

This is a wonderful addition to the item presently being discussed.

Driveshaft Assembly Front Heavy Duty Stampede 4X4

This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas

FUNCTIONS:
Black plastic and steel building

INCLUDES:
Front driveshaft assembly
Screw pin

REQUIRES:
Installation on automobile

Right here is a fantastic item that numerous others have purchased the exact same time.

Alum Bearing Adapter Slash 4X4

This is an optional Bearing Adapter for the Slash 4X4.

FUNCTIONS:
6061-T6 anodized blue aluminum building
Steel 10x15x4mm ball bearing with blue rubber seal
Utilized on slipper shaft

INCLUDES:
One aluminum adapter
One 10x15x4mm ball bearing

REQUIRES:
Installation on to slipper shaft
Staying clutch pieces

This item compliments the above discussed item.

Front Or Rear A-Arms For Traxxas Slash 4X4 And Rustler 4X4, Blac

These are the optional RPM Heavy Duty Front/Rear A-Arms
for the Traxxas Slash 4x4.

FUNCTIONS:
Black in color
Plastic constrution

INCLUDES:
Two Front/Rear A-Arms

REQUIRES:
Installation at front or rear suspension

SPECIFICATIONS:
Length: 3.96" (100.5mm)
Width: 1.79" (45.5mm) at widest point
Density: 0.31" (8mm)

REMARKS:
Likewise available in Blue (RPMC0705)