HPI Split Washer, 3X6mm, (20Pcs)

These are the 3x6mm Spring Washers from HPI Racing.

FEATURES:
Steel building and construction
Silver in color

CONSISTS OF:
Twenty 3x6mm Spring Washers

SPECS:
Outer Diameter: 6mm
Inner Diameter: 3mm

Regularly acquired with the product that you are presently checking out.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal 4 Plug System permits connectivity in between today's
    four most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    merely connect desired plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Cars and truck balancer (TCPP9150)

SPECS:
Setup: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Min Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

REMARKS:
READ the ENTIRE guideline sheet included with battery before use
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER allow to Release below 2.5V per cell
NEVER dismantle or customize pack electrical wiring in any method or leak cells
NEVER place on combustible products or leave ignored during
charging
ALWAYS charge in a fireproof place
ALWAYS set charger's output volts to match battery volts
CONSTANTLY stay out of reach of children

Right here is a excellent product that lots of others have purchased the very same time.

Flanged Lock Nut, M4, (4Pcs), Bullet St/Mt, Rs4, Venture, Sport

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be utilized for wheels, slipper clutch springs, & other applications
    which require easy removal and will not loosen due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECS:
Diameter: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")

This product praises the above gone over product.

2-Speed Set Screw M3x3mm (6)

These are 3x3mm Set Screws by HPI.

FEATURES:
Plain silver metal construction.
Hexagon socket drive insert.

INCLUDES:
(6) Set Screws

SPECS:
Thread: 3mm (0.118")
Length: 3mm (0.118")

This product praises the main item here.

Set Screw M4x4mm Proceed (4)

These are 4x4mm Set Screws by HPI.

FEATURES:
Steel Set Screws

CONSISTS OF:
4 4x4mm Set Screws

This product praises the main item here.

Cap Head Screw, M2.6X14mm, Hex Socket, Bullet Mt/St (10Pcs)

This is the Button Head Screw M2.6*14mm
For the HPI Racing Bullet Series

FUNCTIONS:
Black colored steel building and construction

CONSISTS OF:
Ten button head screws

REMARKS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)