HPI Shock Shaft, 3X52mm, Bullet Mt/St (Pair)

This is the Shock Shaft 3x52mm
For the HPI Racing Bullet Series

FEATURES:
Steel construction

CONSISTS OF:
Two shock shafts

COMMENTS:
This shaft can be installed on
1/10 Bullet ST Flux 2.4GHz RTR (HPID7008)
1/10 Bullet MT Flux 2.4GHz RTR (HPID7010)
1/10 Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
1/10 Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Get this product to boost the one you read about.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System allows connectivity in between today's
    four most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    merely connect preferred plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Automobile balancer (TCPP9150)

SPECIFICATIONS:
Setup: 2S
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Min Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

COMMENTS:
READ the ENTIRE instruction sheet consisted of with battery before use
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER permit to Release below 2.5V per cell
NEVER dismantle or customize pack circuitry in any way or puncture cells
NEVER put on flammable materials or leave ignored throughout
charging
ALWAYS charge in a fireproof location
ALWAYS set charger's output volts to match battery volts
ALWAYS stay out of reach of children

Get this product to boost the one you read about.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FEATURES:
Black colored steel construction

CONSISTS OF:
One spring

COMMENTS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

The below product also pairs really well with the product being talked about.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FEATURES:
Steel construction

CONSISTS OF:
Two Shock Springs

COMMENTS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)