HPI Shock Shaft, 3X52mm, Bullet Mt/St (Pair)

This is the Shock Shaft 3x52mm
For the HPI Racing Bullet Series

FUNCTIONS:
Steel construction

CONSISTS OF:
2 shock shafts

REMARKS:
This shaft can be installed on
1/10 Bullet ST Flux 2.4GHz RTR (HPID7008)
1/10 Bullet MT Flux 2.4GHz RTR (HPID7010)
1/10 Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
1/10 Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Get this item to improve the one you are reading about.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal 4 Plug System permits connectivity in between today's
    four most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect wanted plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Automobile balancer (TCPP9150)

SPECIFICATIONS:
Setup: TWO
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Minutes Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

REMARKS:
CHECK OUT the ENTIRE direction sheet included with battery before usage
ALWAYS utilize a LiPo-approved Battery charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER EVER Trickle Charge
NEVER permit to Discharge below 2.5V per cell
NEVER take apart or modify pack circuitry in any method or puncture cells
NEVER place on flammable materials or leave ignored during
charging
ALWAYS charge in a fireproof location
ALWAYS set battery charger's output volts to match battery volts
CONSTANTLY keep out of reach of kids

Get this item to improve the one you are reading about.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FUNCTIONS:
Black colored steel construction

CONSISTS OF:
One spring

REMARKS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

The listed below item likewise sets truly well with the item being gone over.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FUNCTIONS:
Steel construction

CONSISTS OF:
2 Shock Springs

REMARKS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)