HPI Shock Shaft, 3X52mm, Bullet Mt/St (Pair)

This is the Shock Shaft 3x52mm
For the HPI Racing Bullet Series

FEATURES:
Steel building

CONSISTS OF:
2 shock shafts

COMMENTS:
This shaft can be set up on
1/10 Bullet ST Flux 2.4GHz RTR (HPID7008)
1/10 Bullet MT Flux 2.4GHz RTR (HPID7010)
1/10 Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
1/10 Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Get this item to boost the one you are reading about.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System allows connectivity between today's
    four most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    just attach preferred plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Automobile balancer (TCPP9150)

SPECIFICATIONS:
Setup: 2S
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Minutes Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

COMMENTS:
CHECK OUT the ENTIRE direction sheet consisted of with battery prior to use
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER EVER Trickle Charge
NEVER allow to Discharge below 2.5V per cell
NEVER disassemble or customize pack circuitry in any method or leak cells
NEVER place on combustible materials or leave unattended during
charging
ALWAYS charge in a fireproof location
ALWAYS set charger's output volts to match battery volts
ALWAYS stay out of reach of children

Get this item to boost the one you are reading about.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FEATURES:
Black colored steel building

CONSISTS OF:
One spring

COMMENTS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

The below item also sets really well with the item being gone over.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FEATURES:
Steel building

CONSISTS OF:
2 Shock Springs

COMMENTS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)