JavaScript seems to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website. Click here for instructions on enabling javascript in your browser.

HPI Nitro Star F4.6 V2 Engine, 4.6Cc, Slide Carburettor, And Rear Ex (HPI 111595 | HPI111595)
Attn Utah Customers, Please use our "Curbside Pickup" option as much as possible. Lean More

Due to the impact of the COVID-19/Corona virus, there my be delays in the shipping estimates shown on our site.

We appreciate your understanding and support during these uncertain times.

Model: HPI 111595
Dist. #: HPIG1595   SKU: HPI111595

Be the first to review this product. (Write Review)

Shipping: In Stock For Shipping
Store Pickup:

South Jordan, UT
Ship To Store - Pick up in 1 to 2 days..

List Price:  $279.99
Price:  $251.99
You Save:  $28 (10%)

This item will earn you 252 reward point(s).
252 points = $5.04 off your next order. Learn More

Updated on Jun 3, 2020 02:15:27 PM

Nitro Star F4.6 V2 Engine w/PS...
This is the HPI Nitro Star F4.6 V2 Monster Truck Engine with Pull Starter.

FEATURES:
Fits any HPI Savage or other 1/8 scale beast truck
1.3oz (37g) lighter and 0.47" (12mm) shorter than previous version
Larger fins on cylinder head for enhanced cooling
New pull starter usages one-way bearing encased in a big 14mm hex for
    increased toughness
Composite body slide valve F1 7.5mm carburetor
8 ports, 7 consumption, one exhaust
Two year restricted guarantee begining at date of purchase, Valid only
    on engines sold and utilized in the U.S.A, Canada, and South America

CONSISTS OF:
F4.6 V2 Monster Truck Engine with Pull Beginner, Cold R5 Radiance Plug,
    Air Filter, and Directions

REQUIRES:
Shine Fuel: 15-25% vehicle blend, 20% needed for burglary
Air filter oil
Radiance starter and track equipment
SPECIFICATIONS:
Displacement: 4.6cc
Bore: 18.68mm
Stroke: 16.6mm
Power: 2.9hp @ 32,000RPM
Distance in between Mounting Hole Centers/Same Side: 083" (21mm)
Distance in between Mounting Hole Centers/Opposite Side: 1.46" (37.2mm)
Crankcase Width below Mounting Tabs: 1.25" (32mm)
Width at Mounting Tabs: 1.8" (46mm)
Height/bottom of Mounting Tab/top of Cylinder Head: 3.5" (88mm)
Height/bottom of Crankcase/top of Cylinder Head: 4" (102mm)
Length/Pull Beginner to Front Bearing: 3.3" (84mm)
Length/Pull Beginner to end of Crankshaft: 4.5" (114mm)

Carburetor Settings:
    High Speed Needle, 2-2/2 turns clockwise from flush
    Idle Screw: Set throttle trim on transmitter so that throttle remains in
neutral position, turn screw counter-clockwise to lower idle
speed, or clockwise to increase idle speed. Set idle speed high
enough to keep engine running smoothly, however low enough to
engage the clutch.
    Low Speed Needle: No change suggested. For increased
efficiency, set after high-speed needle is adjusted. Turn needle
in 1/8 turn increments for much better bottom end throttle response.
Caution-never turn in more than 2 turns from flush. This will
trigger engine to run too lean and will lead to damage.

NOTES:
The front bearing is 19x7x6, the rear bearing is 25x14x6 jxs 10/23/14

Customers who bought this product also purchased

Visual Parts Finder
";