HPI Heavy Duty Drive Shaft 6x84mm

This is the Heavy Duty Drive Shaft 6x84mm
For the HPI Racing Bullet Series

FEATURES:
Steel building and construction

CONSISTS OF:
2 driveshafts

COMMENTS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

This item praises the main item below.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal 4 Plug System enables connection between today's
    four most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect wanted plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Vehicle balancer (TCPP9150)

SPECIFICATIONS:
Setup: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Minutes Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

COMMENTS:
READ the ENTIRE direction sheet consisted of with battery prior to usage
ALWAYS utilize a LiPo-approved Charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER Trickle Charge
NEVER allow to Release below 2.5V per cell
NEVER disassemble or modify pack wiring in any way or leak cells
NEVER put on flammable products or leave unattended throughout
charging
ALWAYS charge in a fire-resistant place
ALWAYS set charger's output volts to match battery volts
CONSTANTLY stay out of reach of kids

The listed below item additionally sets really well with the item being discussed.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to safeguard versus dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECIFICATIONS:
Size: 5mm x 10mm

Get this item to boost the one you are reading about.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FEATURES:
Black colored steel building and construction

CONSISTS OF:
One spring

COMMENTS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)