HPI Heavy Duty Drive Shaft 6x84mm

This is the Sturdy Drive Shaft 6x84mm
For the HPI Racing Bullet Series

FEATURES:
Steel construction

INCLUDES:
Two driveshafts

COMMENTS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

This thing compliments the main item below.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal Four Plug System enables connection between today's
    four most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect preferred plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Car balancer (TCPP9150)

SPECIFICATIONS:
Setup: 2S
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Minutes Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

COMMENTS:
READ the ENTIRE instruction sheet consisted of with battery before use
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER Trickle Charge
NEVER allow to Release below 2.5V per cell
NEVER dismantle or modify pack circuitry in any way or puncture cells
NEVER place on combustible materials or leave unattended throughout
charging
ALWAYS charge in a fire-resistant location
ALWAYS set battery charger's output volts to match battery volts
ALWAYS stay out of reach of children

The listed below thing additionally sets really well with the thing being reviewed.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to protect against dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECIFICATIONS:
Size: 5mm x 10mm

Get this thing to improve the one you are reading about.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FEATURES:
Black colored steel construction

INCLUDES:
One spring

COMMENTS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)