HPI Heavy Duty Drive Shaft 6x84mm

This is the Sturdy Drive Shaft 6x84mm
For the HPI Racing Bullet Series

FEATURES:
Steel construction

CONSISTS OF:
Two driveshafts

REMARKS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

This item compliments the main item below.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System permits connection in between today's
    4 most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    merely attach desired plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Car balancer (TCPP9150)

SPECS:
Setup: 2S
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Minutes Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

REMARKS:
CHECK OUT the ENTIRE direction sheet consisted of with battery prior to use
ALWAYS utilize a LiPo-approved Battery charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER enable to Release below 2.5V per cell
NEVER disassemble or customize pack electrical wiring in any way or puncture cells
NEVER put on combustible materials or leave ignored during
charging
ALWAYS charge in a fire-resistant location
ALWAYS set charger's output volts to match battery volts
CONSTANTLY stay out of reach of kids

The below item likewise sets truly well with the item being gone over.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to safeguard against dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECS:
Size: 5mm x 10mm

Get this item to enhance the one you are reading around.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FEATURES:
Black colored steel construction

CONSISTS OF:
One spring

REMARKS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)