HPI Gear Shaft 5x29mm (2)

This is a pair of 5x29mm Equipment Shafts for the
HPI Savage XS Flux Mini Monster Truck.

FEATURES:
Constructed of hardened steel

INCLUDES:
2 5x29mm Equipment Shafts

NEEDS:
Setting up in drive systems following instructions in handbook

This is a superb enhancement to the item currently being reviewed.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal Four Plug System allows connectivity in between today's
    four most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect preferred plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Car balancer (TCPP9150)

SPECS:
Setup: 2S
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Min Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

REMARKS:
READ the ENTIRE direction sheet included with battery prior to usage
ALWAYS utilize a LiPo-approved Battery charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER EVER Trickle Charge
NEVER allow to Discharge below 2.5V per cell
NEVER disassemble or modify pack electrical wiring in any method or leak cells
NEVER put on combustible materials or leave unattended throughout
charging
ALWAYS charge in a fire-resistant place
ALWAYS set charger's output volts to match battery volts
ALWAYS keep out of reach of kids

Several others have purchased this item together with the item that you are currently reading about.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FEATURES:
Black colored steel construction

INCLUDES:
One spring

REMARKS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Several others have purchased this item together with the item that you are currently reading about.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FEATURES:
Steel construction

INCLUDES:
2 Shock Springs

REMARKS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Right here is a wonderful item that numerous others have purchased the same time.

Differential Gear Set, Bullet Mt/St

This is the Diff Equipment Set
For the HPI Racing WRI and Bullet Series

FEATURES:
Steel construction
Fits the WR8 Flux, Bullet MT and ST Flux, Bullet MT and ST Nitro
Also fits all three gearboxes of the D413 Buggy Package from Hot Bodies

INCLUDES:
2 big bevel gears
Four little bevel gears

REMARKS:
This differential equipment set can be installed on
1/8 WR8 3.0 Ford Feast Rally Abu Dhabi RTR
1/10 Bullet MT Flux 2.4GHz RTR
1/10 Bullet ST Flux 2.4GHz RTR
1/10 Bullet MT 3.0 Nitro 2.4GHz RTR
1/10 Bullet ST 3.0 Nitro 2.4GHz RTR