HPI Gear Shaft 5x29mm (2)

This is a pair of 5x29mm Equipment Shafts for the
HPI Savage XS Flux Mini Monster Truck.

FEATURES:
Constructed of solidified steel

CONSISTS OF:
2 5x29mm Equipment Shafts

NEEDS:
Installing in drive systems following guidelines in handbook

This is a fantastic enhancement to the thing currently being gone over.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal 4 Plug System allows connection between today's
    4 most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect wanted plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Automobile balancer (TCPP9150)

SPECS:
Setup: 2S
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Minutes Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

COMMENTS:
READ the ENTIRE direction sheet consisted of with battery before usage
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER Trickle Charge
NEVER permit to Release below 2.5V per cell
NEVER take apart or modify pack circuitry in any method or leak cells
NEVER place on combustible products or leave unattended during
charging
ALWAYS charge in a fire-resistant place
ALWAYS set battery charger's output volts to match battery volts
CONSTANTLY stay out of reach of children

Lots of others have actually gotten this thing together with the thing that you are currently reading about.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FEATURES:
Black colored steel building and construction

CONSISTS OF:
One spring

COMMENTS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Lots of others have actually gotten this thing together with the thing that you are currently reading about.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FEATURES:
Steel building and construction

CONSISTS OF:
2 Shock Springs

COMMENTS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Here is a wonderful thing that numerous others have actually bought at the very same time.

Differential Gear Set, Bullet Mt/St

This is the Diff Equipment Set
For the HPI Racing WRI and Bullet Series

FEATURES:
Steel building and construction
Fits the WR8 Flux, Bullet MT and ST Flux, Bullet MT and ST Nitro
Also fits all three gearboxes of the D413 Buggy Set from Hot Bodies

CONSISTS OF:
2 large bevel equipments
4 little bevel equipments

COMMENTS:
This differential equipment set can be set up on
1/8 WR8 3.0 Ford Fiesta Rally Abu Dhabi RTR
1/10 Bullet MT Flux 2.4GHz RTR
1/10 Bullet ST Flux 2.4GHz RTR
1/10 Bullet MT 3.0 Nitro 2.4GHz RTR
1/10 Bullet ST 3.0 Nitro 2.4GHz RTR