HPI Gear Shaft 5x29mm (2)

This is a set of 5x29mm Equipment Shafts for the
HPI Savage XS Flux Mini Monster Truck.

FEATURES:
Constructed of hardened steel

CONSISTS OF:
Two 5x29mm Equipment Shafts

REQUIRES:
Setting up in drive systems following directions in manual

This is a fantastic addition to the item presently being discussed.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal Four Plug System enables connectivity between today's
    four most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    simply attach wanted plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Vehicle balancer (TCPP9150)

SPECIFICATIONS:
Configuration: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Min Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

COMMENTS:
READ the ENTIRE instruction sheet included with battery before use
ALWAYS utilize a LiPo-approved Charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER enable to Discharge below 2.5V per cell
NEVER disassemble or customize pack circuitry in any method or leak cells
NEVER put on combustible materials or leave ignored throughout
charging
ALWAYS charge in a fire-resistant place
ALWAYS set charger's output volts to match battery volts
CONSTANTLY stay out of reach of kids

Numerous others have actually acquired this item along with the item that you are presently checking out.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FUNCTIONS:
Black colored steel construction

CONSISTS OF:
One spring

COMMENTS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Numerous others have actually acquired this item along with the item that you are presently checking out.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FUNCTIONS:
Steel construction

CONSISTS OF:
Two Shock Springs

COMMENTS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Here is a wonderful item that lots of others have actually bought at the exact same time.

Differential Gear Set, Bullet Mt/St

This is the Diff Equipment Set
For the HPI Racing WRI and Bullet Series

FUNCTIONS:
Steel construction
Fits the WR8 Flux, Bullet MT and ST Flux, Bullet MT and ST Nitro
Likewise fits all 3 gearboxes of the D413 Buggy Set from Hot Bodies

CONSISTS OF:
Two large bevel equipments
Four little bevel equipments

COMMENTS:
This differential equipment set can be installed on
1/8 WR8 3.0 Ford Fiesta Rally Abu Dhabi RTR
1/10 Bullet MT Flux 2.4GHz RTR
1/10 Bullet ST Flux 2.4GHz RTR
1/10 Bullet MT 3.0 Nitro 2.4GHz RTR
1/10 Bullet ST 3.0 Nitro 2.4GHz RTR