HPI Gear Shaft 5x29mm (2)

This is a pair of 5x29mm Equipment Shafts for the
HPI Savage XS Flux Mini Beast Truck.

FEATURES:
Constructed of hardened steel

CONSISTS OF:
2 5x29mm Equipment Shafts

NEEDS:
Setting up in drive systems following directions in manual

This is a fantastic enhancement to the thing presently being reviewed.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System allows connection in between today's
    four most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    merely attach preferred plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Vehicle balancer (TCPP9150)

SPECIFICATIONS:
Configuration: 2S
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Minutes Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

REMARKS:
READ the ENTIRE guideline sheet included with battery before usage
ALWAYS utilize a LiPo-approved Charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER Trickle Charge
NEVER permit to Release below 2.5V per cell
NEVER disassemble or customize pack electrical wiring in any way or puncture cells
NEVER put on combustible materials or leave unattended during
charging
ALWAYS charge in a fireproof area
ALWAYS set battery charger's output volts to match battery volts
ALWAYS stay out of reach of kids

Numerous others have acquired this thing along with the thing that you are presently checking out.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FUNCTIONS:
Black colored steel building and construction

CONSISTS OF:
One spring

REMARKS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Numerous others have acquired this thing along with the thing that you are presently checking out.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FUNCTIONS:
Steel building and construction

CONSISTS OF:
2 Shock Springs

REMARKS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Here is a wonderful thing that many others have purchased the same time.

Differential Gear Set, Bullet Mt/St

This is the Diff Equipment Set
For the HPI Racing WRI and Bullet Series

FUNCTIONS:
Steel building and construction
Fits the WR8 Flux, Bullet MT and ST Flux, Bullet MT and ST Nitro
Also fits all 3 gearboxes of the D413 Buggy Set from Hot Bodies

CONSISTS OF:
2 large bevel equipments
Four little bevel equipments

REMARKS:
This differential equipment set can be installed on
1/8 WR8 3.0 Ford Carnival Rally Abu Dhabi RTR
1/10 Bullet MT Flux 2.4GHz RTR
1/10 Bullet ST Flux 2.4GHz RTR
1/10 Bullet MT 3.0 Nitro 2.4GHz RTR
1/10 Bullet ST 3.0 Nitro 2.4GHz RTR