HPI Gear Shaft 5x29mm (2)

This is a pair of 5x29mm Gear Shafts for the
HPI Savage XS Flux Mini Monster Truck.

FEATURES:
Constructed of solidified steel

INCLUDES:
Two 5x29mm Gear Shafts

REQUIRES:
Setting up in drive systems following directions in manual

This is a amazing addition to the product presently being talked about.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System allows connectivity between today's
    4 most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    just attach preferred plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Car balancer (TCPP9150)

SPECS:
Configuration: 2S
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Min Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

REMARKS:
READ the ENTIRE guideline sheet consisted of with battery before usage
ALWAYS utilize a LiPo-approved Charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER allow to Release listed below 2.5V per cell
NEVER take apart or customize pack wiring in any way or leak cells
NEVER place on flammable products or leave unattended during
charging
ALWAYS charge in a fire-resistant area
ALWAYS set charger's output volts to match battery volts
CONSTANTLY stay out of reach of kids

Numerous others have bought this product along with the product that you are presently checking out.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FEATURES:
Black colored steel building

INCLUDES:
One spring

REMARKS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Numerous others have bought this product along with the product that you are presently checking out.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FEATURES:
Steel building

INCLUDES:
Two Shock Springs

REMARKS:
The HPI Racing Bullet Series consists of
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Right here is a wonderful product that several others have purchased the same time.

Differential Gear Set, Bullet Mt/St

This is the Diff Gear Set
For the HPI Racing WRI and Bullet Series

FEATURES:
Steel building
Fits the WR8 Flux, Bullet MT and ST Flux, Bullet MT and ST Nitro
Also fits all 3 transmissions of the D413 Buggy Kit from Hot Bodies

INCLUDES:
Two large bevel equipments
Four small bevel equipments

REMARKS:
This differential equipment set can be installed on
1/8 WR8 3.0 Ford Feast Rally Abu Dhabi RTR
1/10 Bullet MT Flux 2.4GHz RTR
1/10 Bullet ST Flux 2.4GHz RTR
1/10 Bullet MT 3.0 Nitro 2.4GHz RTR
1/10 Bullet ST 3.0 Nitro 2.4GHz RTR