HPI Front/Rear Upright Set Left/Right

These are the Front Knuckles and Back Uprights
for the HPI WR8 and Bullet Series of Vehicles.

FEATURES:
Plastic construction

INCLUDES:
Left and Right Front Knuckles and Back Uprights with 4 Hex Inserts

You will enjoy this item if you have the item earlier discussed.

Front Hub Carriers (10 Degrees), Bullet Mt/St

These are the Front Hub Carriers for the HPI WR8 and Bullet Series.

FEATURES:
Plastic construction

INCLUDES:
Left and Right Front Hub Carriers

NEEDS:
Four 5x10mm Ball Bearings, DTXC1535

You will enjoy this item if you have the item earlier discussed.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal Four Plug System enables connection between today's
    4 most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    just attach wanted plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Vehicle balancer (TCPP9150)

SPECS:
Configuration: 2S
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Minutes Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

REMARKS:
CHECK OUT the ENTIRE instruction sheet consisted of with battery before usage
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER enable to Release below 2.5V per cell
NEVER disassemble or customize pack electrical wiring in any method or puncture cells
NEVER put on flammable materials or leave ignored throughout
charging
ALWAYS charge in a fire-resistant place
ALWAYS set battery charger's output volts to match battery volts
ALWAYS stay out of reach of kids

This thing compliments the main item right here.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to safeguard against dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECS:
Size: 5mm x 10mm

This thing is often bought with the above stated thing.

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be used for wheels, slipper clutch springs, & other applications
    which need simple removal and will not loosen due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECS:
Size: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")