HPI Front/Rear Upright Set Left/Right

These are the Front Knuckles and Rear Uprights
for the HPI WR8 and Bullet Series of Vehicles.

FEATURES:
Plastic construction

INCLUDES:
Left and Right Front Knuckles and Rear Uprights with four Hex Inserts

You will enjoy this item if you have the item previously mentioned.

Front Hub Carriers (10 Degrees), Bullet Mt/St

These are the Front Center Carriers for the HPI WR8 and Bullet Series.

FEATURES:
Plastic construction

INCLUDES:
Left and Right Front Center Carriers

NEEDS:
4 5x10mm Ball Bearings, DTXC1535

You will enjoy this item if you have the item previously mentioned.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal 4 Plug System allows connectivity in between today's
    four most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    just attach desired plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Car balancer (TCPP9150)

SPECIFICATIONS:
Setup: TWO
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Minutes Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

REMARKS:
CHECK OUT the ENTIRE instruction sheet included with battery prior to usage
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER permit to Discharge below 2.5V per cell
NEVER disassemble or modify pack electrical wiring in any method or puncture cells
NEVER put on flammable products or leave ignored throughout
charging
ALWAYS charge in a fire-resistant place
ALWAYS set battery charger's output volts to match battery volts
CONSTANTLY stay out of reach of children

This item compliments the main item here.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to protect against dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECIFICATIONS:
Size: 5mm x 10mm

This item is frequently bought with the above stated item.

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be used for wheels, slipper clutch springs, & other applications
    which need easy removal and will not loosen up due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECIFICATIONS:
Diameter: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")