HPI Front/Rear Upright Set Left/Right

These are the Front Knuckles and Back Uprights
for the HPI WR8 and Bullet Series of Vehicles.

FEATURES:
Plastic building

INCLUDES:
Left and Right Front Knuckles and Back Uprights with four Hex Inserts

You will love this item if you have the item above mentioned.

Front Hub Carriers (10 Degrees), Bullet Mt/St

These are the Front Center Carriers for the HPI WR8 and Bullet Series.

FEATURES:
Plastic building

INCLUDES:
Left and Right Front Center Carriers

NEEDS:
4 5x10mm Ball Bearings, DTXC1535

You will love this item if you have the item above mentioned.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal 4 Plug System enables connection between today's
    four most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    simply connect desired plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Vehicle balancer (TCPP9150)

SPECS:
Setup: 2S
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Min Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

COMMENTS:
READ the ENTIRE direction sheet consisted of with battery prior to usage
ALWAYS utilize a LiPo-approved Battery charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER allow to Release below 2.5V per cell
NEVER dismantle or customize pack wiring in any way or puncture cells
NEVER put on flammable products or leave ignored during
charging
ALWAYS charge in a fireproof place
ALWAYS set battery charger's output volts to match battery volts
CONSTANTLY stay out of reach of kids

This item praises the main item below.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to protect against dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECS:
Size: 5mm x 10mm

This item is often bought with the above pointed out item.

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be used for wheels, slipper clutch springs, & other applications
    which need easy elimination and will not loosen up due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECS:
Diameter: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")