JavaScript seems to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website. Click here for instructions on enabling javascript in your browser.

HPI Front/Rear Upright Set Left/Right (HPI 101208 | HPI101208)
Due to the impact of the COVID-19/Corona virus, there my be delays in the shipping estimates shown on our site.

We appreciate your understanding and support during these uncertain times.

Model: HPI 101208
Dist. #: HPIC4208   SKU: HPI101208

Be the first to review this product. (Write Review)

Shipping: In Stock For Shipping
Store Pickup:

South Jordan, UT
Available Now!

Price:  $10.99

This item will earn you 11 reward point(s).
11 points = $0.22 off your next order. Learn More

Updated on May 16, 2022 07:06:19 PM

Front/Rear Upright Set Left/Right...
These are the Front Knuckles and Rear Uprights
for the HPI WR8 and Bullet Series of Vehicles.

FEATURES:
Plastic building and construction

INCLUDES:
Left and Right Front Knuckles and Rear Uprights with 4 Hex Inserts

You will enjoy this thing if you have the thing earlier mentioned.

Front Hub Carriers (10 Degrees), Bullet Mt/St

These are the Front Center Providers for the HPI WR8 and Bullet Series.

FEATURES:
Plastic building and construction

INCLUDES:
Left and Right Front Center Providers

NEEDS:
Four 5x10mm Ball Bearings, DTXC1535

You will enjoy this thing if you have the thing earlier mentioned.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System permits connection between today's
    4 most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect preferred plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Car balancer (TCPP9150)

SPECS:
Setup: TWO
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Min Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

REMARKS:
CHECK OUT the ENTIRE guideline sheet consisted of with battery prior to use
ALWAYS use a LiPo-approved Battery charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER Trickle Charge
NEVER enable to Discharge below 2.5V per cell
NEVER dismantle or modify pack wiring in any way or leak cells
NEVER put on flammable products or leave ignored throughout
charging
ALWAYS charge in a fire-resistant location
ALWAYS set battery charger's output volts to match battery volts
CONSTANTLY stay out of reach of children

This thing compliments the main item right here.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to safeguard against dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECS:
Size: 5mm x 10mm

This thing is frequently bought with the above pointed out thing.

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be used for wheels, slipper clutch springs, & other applications
    which need easy removal and will not loosen due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECS:
Diameter: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")

Frequently Bought Together

HPI Front/Rear Upright Set Left/Right
+
HPI Heavy Duty Drive Shaft 6x84mm
+
HPI Front Hub Carriers (10 Degrees), Bullet Mt/St
This Item: HPI Front/Rear Upright Set Left/Right
$10.99
HPI Heavy Duty Drive Shaft 6x84mm
$11.99
HPI Front Hub Carriers (10 Degrees), Bullet Mt/St
$6.99

Total Price: $29.97

Add All Three To Cart

Customers who bought this product also purchased

Visual Parts Finder
";