HPI Front/Rear Upright Set Left/Right

These are the Front Knuckles and Back Uprights
for the HPI WR8 and Bullet Series of Vehicles.

FEATURES:
Plastic building

CONSISTS OF:
Left and Right Front Knuckles and Back Uprights with four Hex Inserts

You will love this thing if you have the thing earlier mentioned.

Front Hub Carriers (10 Degrees), Bullet Mt/St

These are the Front Hub Providers for the HPI WR8 and Bullet Series.

FEATURES:
Plastic building

CONSISTS OF:
Left and Right Front Hub Providers

REQUIRES:
Four 5x10mm Ball Bearings, DTXC1535

You will love this thing if you have the thing earlier mentioned.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System enables connectivity in between today's
    four most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    merely attach desired plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Automobile balancer (TCPP9150)

SPECIFICATIONS:
Setup: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Min Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

COMMENTS:
READ the ENTIRE guideline sheet consisted of with battery before usage
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER permit to Release below 2.5V per cell
NEVER take apart or customize pack circuitry in any way or leak cells
NEVER place on combustible products or leave ignored throughout
charging
ALWAYS charge in a fire-resistant place
ALWAYS set charger's output volts to match battery volts
CONSTANTLY keep out of reach of kids

This thing compliments the main item right here.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to protect against dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECIFICATIONS:
Size: 5mm x 10mm

This thing is often purchased with the above stated thing.

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be utilized for wheels, slipper clutch springs, & other applications
    which need simple removal and will not loosen due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECIFICATIONS:
Size: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")