HPI Front/Rear Upright Set Left/Right

These are the Front Knuckles and Rear Uprights
for the HPI WR8 and Bullet Series of Vehicles.

FEATURES:
Plastic building and construction

INCLUDES:
Left and Right Front Knuckles and Rear Uprights with 4 Hex Inserts

You will love this product if you have the product just above pointed out.

Front Hub Carriers (10 Degrees), Bullet Mt/St

These are the Front Hub Providers for the HPI WR8 and Bullet Series.

FEATURES:
Plastic building and construction

INCLUDES:
Left and Right Front Hub Providers

NEEDS:
Four 5x10mm Ball Bearings, DTXC1535

You will love this product if you have the product just above pointed out.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System enables connection in between today's
    4 most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect wanted plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Automobile balancer (TCPP9150)

SPECIFICATIONS:
Configuration: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Minutes Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

COMMENTS:
READ the ENTIRE instruction sheet consisted of with battery before usage
ALWAYS utilize a LiPo-approved Charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER EVER Trickle Charge
NEVER allow to Release listed below 2.5V per cell
NEVER take apart or modify pack wiring in any way or puncture cells
NEVER place on flammable materials or leave ignored throughout
charging
ALWAYS charge in a fire-resistant location
ALWAYS set battery charger's output volts to match battery volts
CONSTANTLY stay out of reach of children

This thing praises the main item below.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to safeguard versus dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECIFICATIONS:
Size: 5mm x 10mm

This thing is frequently acquired with the above discussed thing.

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be utilized for wheels, slipper clutch springs, & other applications
    which require easy elimination and will not loosen due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECIFICATIONS:
Diameter: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")