HPI Front/Rear Upright Set Left/Right

These are the Front Knuckles and Back Uprights
for the HPI WR8 and Bullet Series of Vehicles.

FEATURES:
Plastic construction

CONSISTS OF:
Left and Right Front Knuckles and Back Uprights with 4 Hex Inserts

You will certainly like this item if you have the item just above discussed.

Front Hub Carriers (10 Degrees), Bullet Mt/St

These are the Front Hub Providers for the HPI WR8 and Bullet Series.

FEATURES:
Plastic construction

CONSISTS OF:
Left and Right Front Hub Providers

REQUIRES:
Four 5x10mm Ball Bearings, DTXC1535

You will certainly like this item if you have the item just above discussed.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal Four Plug System permits connection in between today's
    4 most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    merely attach preferred plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Automobile balancer (TCPP9150)

SPECS:
Setup: 2S
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Minutes Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

REMARKS:
CHECK OUT the ENTIRE direction sheet included with battery prior to use
ALWAYS utilize a LiPo-approved Charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER permit to Release below 2.5V per cell
NEVER take apart or customize pack circuitry in any way or puncture cells
NEVER place on combustible products or leave ignored throughout
charging
ALWAYS charge in a fire-resistant location
ALWAYS set charger's output volts to match battery volts
ALWAYS stay out of reach of children

This product compliments the main item here.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to protect versus dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECS:
Size: 5mm x 10mm

This product is regularly bought with the above pointed out product.

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be used for wheels, slipper clutch springs, & other applications
    which require easy elimination and will not loosen due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECS:
Size: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")