HPI Front/Rear Upright Set Left/Right

These are the Front Knuckles and Rear Uprights
for the HPI WR8 and Bullet Series of Vehicles.

FEATURES:
Plastic construction

INCLUDES:
Left and Right Front Knuckles and Rear Uprights with 4 Hex Inserts

You will love this thing if you have the thing previously discussed.

Front Hub Carriers (10 Degrees), Bullet Mt/St

These are the Front Center Providers for the HPI WR8 and Bullet Series.

FEATURES:
Plastic construction

INCLUDES:
Left and Right Front Center Providers

REQUIRES:
Four 5x10mm Ball Bearings, DTXC1535

You will love this thing if you have the thing previously discussed.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal Four Plug System enables connectivity between today's
    4 most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect desired plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Car balancer (TCPP9150)

SPECS:
Configuration: 2S
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Minutes Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

COMMENTS:
READ the ENTIRE instruction sheet consisted of with battery before use
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER enable to Discharge listed below 2.5V per cell
NEVER disassemble or modify pack circuitry in any method or leak cells
NEVER place on flammable materials or leave unattended during
charging
ALWAYS charge in a fire-resistant area
ALWAYS set battery charger's output volts to match battery volts
CONSTANTLY keep out of reach of kids

This product compliments the main item here.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to safeguard versus dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECS:
Size: 5mm x 10mm

This product is often purchased with the above pointed out product.

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be utilized for wheels, slipper clutch springs, & other applications
    which require simple removal and will not loosen due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECS:
Size: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")