HPI Cap Head Screw M3x10 (6)

This is a package of 3x10mm Caphead Device Screws.

FEATURES:
Plain black steel construction.
High round cap head screw with a hexagon socket drive insert.
These screws can be used anywhere this size is needed.

INCLUDES:
(6) Caphead Device Screws

REQUIRES:
2.5mm Allen/Hex Wrench

SPECIFICATIONS:
Diameter: 3mm
Length: 10mm

This item is frequently bought with the above pointed out item.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal 4 Plug System allows connectivity in between today's
    4 most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    just attach desired plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Automobile balancer (TCPP9150)

SPECIFICATIONS:
Setup: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Min Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

COMMENTS:
CHECK OUT the ENTIRE instruction sheet included with battery prior to usage
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER enable to Release listed below 2.5V per cell
NEVER dismantle or customize pack electrical wiring in any method or puncture cells
NEVER place on flammable materials or leave ignored throughout
charging
ALWAYS charge in a fireproof location
ALWAYS set battery charger's output volts to match battery volts
ALWAYS keep out of reach of children

Right here is a fantastic item that lots of others have actually bought at the very same time.



These are the optional Integy Steering Knuckles for the
1/10 scale HPI Bullet MT and Bullet ST.

FEATURES:
Billet machined aluminum building, blue in color

CONSISTS OF:
Two Steering Knuckles

REQUIRES:
4 5x10mm ball bearings, order 2 DTXC1535

This item praises the main item below.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FEATURES:
Black colored steel building

CONSISTS OF:
One spring

COMMENTS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

This is a superb enhancement to the item currently being talked about.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FEATURES:
Steel building

CONSISTS OF:
Two Shock Springs

COMMENTS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)