HPI Cap Head Screw M3x10 (6)

This is a plan of 3x10mm Caphead Machine Screws.

FEATURES:
Plain black steel construction.
High round cap head screw with a hexagon socket drive insert.
These screws can be used anywhere this size is needed.

INCLUDES:
(6) Caphead Machine Screws

NEEDS:
2.5mm Allen/Hex Wrench

SPECS:
Size: 3mm
Length: 10mm

This thing is regularly acquired with the above mentioned thing.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal 4 Plug System enables connection in between today's
    four most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    merely attach wanted plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Car balancer (TCPP9150)

SPECS:
Configuration: TWO
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Min Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

COMMENTS:
READ the ENTIRE instruction sheet consisted of with battery before use
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER enable to Discharge listed below 2.5V per cell
NEVER take apart or customize pack circuitry in any method or puncture cells
NEVER put on combustible products or leave ignored during
charging
ALWAYS charge in a fireproof location
ALWAYS set charger's output volts to match battery volts
CONSTANTLY keep out of reach of kids

Here is a fantastic thing that lots of others have bought at the same time.



These are the optional Integy Steering Knuckles for the
1/10 scale HPI Bullet MT and Bullet ST.

FEATURES:
Billet machined aluminum construction, blue in color

CONSISTS OF:
Two Steering Knuckles

NEEDS:
4 5x10mm ball bearings, order 2 DTXC1535

This thing compliments the main item here.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FUNCTIONS:
Black colored steel construction

CONSISTS OF:
One spring

COMMENTS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

This is a wonderful addition to the thing currently being gone over.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FUNCTIONS:
Steel construction

CONSISTS OF:
Two Shock Springs

COMMENTS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)