HPI Binder Head Screw, M3x8mm, (10Pcs)

These are 3x8mm Binder Head Screws from HPI Racing.
(Penny not consisted of)
FEATURES:
Plain black steel construction.
Binder head with a phillips recess drive insert.
Used for lots of applications in all HPI cars and trucks

INCLUDES:
(10) Screws

SPECS:
Length: 8mm
Size: 3mm

You will love this product if you have the product just above pointed out.

Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to secure versus dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECS:
Size: 5mm x 10mm

This product compliments the main item below.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal 4 Plug System permits connectivity in between today's
    four most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    merely connect desired plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Vehicle balancer (TCPP9150)

SPECS:
Configuration: TWO
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Min Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

COMMENTS:
READ the ENTIRE instruction sheet consisted of with battery before usage
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER permit to Release below 2.5V per cell
NEVER take apart or modify pack electrical wiring in any way or puncture cells
NEVER place on flammable materials or leave ignored during
charging
ALWAYS charge in a fire-resistant location
ALWAYS set battery charger's output volts to match battery volts
CONSTANTLY stay out of reach of kids

Want an additional great product to match the above mentioned product?

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FEATURES:
Black colored steel building

INCLUDES:
One spring

COMMENTS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Right here is an additional product that compliments the product being gone over.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FEATURES:
Steel building

INCLUDES:
Two Shock Springs

COMMENTS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)