HPI Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to safeguard versus dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECS:
Size: 5mm x 10mm

Regularly gotten with the product that you are presently checking out.

Binder Head Screw, M3x8mm, (10Pcs)

These are 3x8mm Binder Head Screws from HPI Racing.
(Penny not included)
FEATURES:
Plain black steel construction.
Binder head with a phillips recess drive insert.
Used for many applications in all HPI cars and trucks

INCLUDES:
(10) Screws

SPECS:
Length: 8mm
Diameter: 3mm

You will like this thing if you have the thing previously stated.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal Four Plug System permits connectivity between today's
    four most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    just attach desired plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Vehicle balancer (TCPP9150)

SPECS:
Setup: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Minutes Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

REMARKS:
CHECK OUT the ENTIRE direction sheet included with battery prior to use
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER Trickle Charge
NEVER permit to Discharge listed below 2.5V per cell
NEVER disassemble or customize pack electrical wiring in any method or leak cells
NEVER put on flammable products or leave ignored during
charging
ALWAYS charge in a fireproof location
ALWAYS set charger's output volts to match battery volts
CONSTANTLY keep out of reach of kids

Want one more great product to compliment the above pointed out product?

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be utilized for wheels, slipper clutch springs, & other applications
    which require easy removal and will not loosen due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECS:
Diameter: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")

Right here is one more product that praises the product being gone over.

2-Speed Set Screw M3x3mm (6)

These are 3x3mm Set Screws by HPI.

FEATURES:
Plain silver metal construction.
Hexagon socket drive insert.

INCLUDES:
(6) Set Screws

SPECS:
Thread: 3mm (0.118")
Length: 3mm (0.118")