HPI Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to safeguard versus dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECIFICATIONS:
Size: 5mm x 10mm

Regularly purchased with the thing that you are currently checking out.

Binder Head Screw, M3x8mm, (10Pcs)

These are 3x8mm Binder Head Screws from HPI Racing.
(Cent not consisted of)
FEATURES:
Plain black steel construction.
Binder head with a phillips recess drive insert.
Used for lots of applications in all HPI vehicles and trucks

INCLUDES:
(10) Screws

SPECIFICATIONS:
Length: 8mm
Size: 3mm

You will enjoy this item if you have the item earlier pointed out.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal 4 Plug System permits connection in between today's
    4 most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    just connect preferred plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable battery charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Automobile balancer (TCPP9150)

SPECIFICATIONS:
Setup: 2S
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Minutes Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

COMMENTS:
CHECK OUT the ENTIRE guideline sheet consisted of with battery before use
ALWAYS utilize a LiPo-approved Battery charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER permit to Discharge below 2.5V per cell
NEVER dismantle or modify pack electrical wiring in any method or leak cells
NEVER put on combustible materials or leave ignored during
charging
ALWAYS charge in a fire-resistant location
ALWAYS set battery charger's output volts to match battery volts
CONSTANTLY keep out of reach of kids

Want another great thing to enhance the above discussed thing?

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be used for wheels, slipper clutch springs, & other applications
    which require easy elimination and will not loosen due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECIFICATIONS:
Size: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")

Below is another thing that compliments the thing being gone over.

2-Speed Set Screw M3x3mm (6)

These are 3x3mm Set Screws by HPI.

FEATURES:
Plain silver metal construction.
Hexagon socket drive insert.

INCLUDES:
(6) Set Screws

SPECIFICATIONS:
Thread: 3mm (0.118")
Length: 3mm (0.118")