HPI Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to secure against dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECS:
Size: 5mm x 10mm

Often acquired with the product that you are currently checking out.

Binder Head Screw, M3x8mm, (10Pcs)

These are 3x8mm Binder Head Screws from HPI Racing.
(Dime not included)
INCLUDES:
Plain black steel construction.
Binder head with a phillips recess drive insert.
Used for many applications in all HPI vehicles and trucks

CONSISTS OF:
(10) Screws

SPECS:
Length: 8mm
Size: 3mm

You will certainly like this product if you have the product above pointed out.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System enables connection between today's
    4 most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    just attach desired plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Automobile balancer (TCPP9150)

SPECS:
Setup: 2S
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Minutes Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

COMMENTS:
CHECK OUT the ENTIRE guideline sheet included with battery prior to usage
ALWAYS utilize a LiPo-approved Battery charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER permit to Discharge below 2.5V per cell
NEVER dismantle or modify pack wiring in any method or puncture cells
NEVER put on combustible products or leave ignored during
charging
ALWAYS charge in a fire-resistant place
ALWAYS set charger's output volts to match battery volts
ALWAYS stay out of reach of children

Want one more fantastic product to enhance the above mentioned product?

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be used for wheels, slipper clutch springs, & other applications
    which need easy elimination and will not loosen due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECS:
Size: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")

Right here is one more product that compliments the product being discussed.

2-Speed Set Screw M3x3mm (6)

These are 3x3mm Set Screws by HPI.

FEATURES:
Plain silver metal construction.
Hexagon socket drive insert.

INCLUDES:
(6) Set Screws

SPECS:
Thread: 3mm (0.118")
Length: 3mm (0.118")