HPI Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to safeguard versus dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECS:
Size: 5mm x 10mm

Regularly acquired with the item that you are currently reading about.

Binder Head Screw, M3x8mm, (10Pcs)

These are 3x8mm Binder Head Screws from HPI Racing.
(Cent not included)
INCLUDES:
Plain black steel construction.
Binder head with a phillips recess drive insert.
Used for many applications in all HPI vehicles and trucks

CONSISTS OF:
(10) Screws

SPECS:
Length: 8mm
Diameter: 3mm

You will certainly like this thing if you have the thing earlier pointed out.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal 4 Plug System allows connection in between today's
    4 most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    merely connect wanted plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Car balancer (TCPP9150)

SPECS:
Configuration: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Constant Discharge 40C (200A)
Min Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

COMMENTS:
READ the ENTIRE instruction sheet included with battery before usage
ALWAYS utilize a LiPo-approved Battery charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "DISCHARGE" lead
NEVER EVER Trickle Charge
NEVER enable to Discharge below 2.5V per cell
NEVER take apart or customize pack circuitry in any way or puncture cells
NEVER put on combustible products or leave unattended throughout
charging
ALWAYS charge in a fireproof place
ALWAYS set charger's output volts to match battery volts
CONSTANTLY keep out of reach of kids

Want an additional great item to enhance the above pointed out item?

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be used for wheels, slipper clutch springs, & other applications
    which need easy elimination and will not loosen up due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECS:
Diameter: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")

Below is an additional item that praises the item being reviewed.

2-Speed Set Screw M3x3mm (6)

These are 3x3mm Set Screws by HPI.

FEATURES:
Plain silver metal construction.
Hexagon socket drive insert.

INCLUDES:
(6) Set Screws

SPECS:
Thread: 3mm (0.118")
Length: 3mm (0.118")