HPI Ball Stud, 4.8X12mm, (10Pcs), Blitz/E-Firestorm/Firestorm 10T

These are the Ball Studs for the HPI Firestorm

FUNCTIONS:
Constructed of steel
Threads into hub carriers and links turnbuckles via ball ends

INCLUDES:
Ten Ball Studs for the HPI Firestorm

REQUIRES:
Threading into hub carriers

Right here is one more thing that praises the thing being discussed.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System allows connection in between today's
    four most typical battery plugs, Tamiya, Traxxas, Deans and EC3,
    simply connect preferred plug to Venom plug on battery's wire leads

INCLUDES:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

REQUIRES:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Automobile balancer (TCPP9150)

SPECS:
Setup: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Minutes Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

REMARKS:
READ the ENTIRE instruction sheet included with battery before usage
ALWAYS use a LiPo-approved Battery charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents greater than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER EVER Trickle Charge
NEVER permit to Release listed below 2.5V per cell
NEVER disassemble or modify pack wiring in any way or puncture cells
NEVER put on combustible products or leave ignored throughout
charging
ALWAYS charge in a fireproof area
ALWAYS set charger's output volts to match battery volts
CONSTANTLY keep out of reach of kids

Right here is one more thing that praises the thing being discussed.

Slipper Clutch Spring, 7X9x1.7Mm, 3 Coils, Bullet Mt/St

This is the Slipper Clutch Spring 7x9x1.7mm 3 Coils
For the HPI Racing Bullet Series

FUNCTIONS:
Black colored steel building and construction

INCLUDES:
One spring

REMARKS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

This thing praises the above discussed thing.

Spring, 13.5X63x1.2Mm, 11 Coils, Bullet Mt/St (2Pcs)

This is the Shock Spring 13.5x63x1.2mm 11 Coils
For the HPI Racing Bullet Series

FUNCTIONS:
Steel building and construction

INCLUDES:
2 Shock Springs

REMARKS:
The HPI Racing Bullet Series includes
Bullet ST Flux 2.4GHz RTR (HPID7008)
Bullet MT Flux 2.4GHz RTR (HPID7010)
Bullet ST 3.0 Nitro 2.4GHz RTR (HPID7004)
Bullet MT 3.0 Nitro 2.4GHz RTR (HPID7006)

Several others have bought this thing in addition to the thing that you are presently reading about.

Differential Gear Set, Bullet Mt/St

This is the Diff Gear Set
For the HPI Racing WRI and Bullet Series

FUNCTIONS:
Steel building and construction
Fits the WR8 Flux, Bullet MT and ST Flux, Bullet MT and ST Nitro
Likewise fits all three transmissions of the D413 Buggy Set from Hot Bodies

INCLUDES:
2 big bevel gears
Four small bevel gears

REMARKS:
This differential gear set can be installed on
1/8 WR8 3.0 Ford Fiesta Rally Abu Dhabi RTR
1/10 Bullet MT Flux 2.4GHz RTR
1/10 Bullet ST Flux 2.4GHz RTR
1/10 Bullet MT 3.0 Nitro 2.4GHz RTR
1/10 Bullet ST 3.0 Nitro 2.4GHz RTR