HPI Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to protect against dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECIFICATIONS:
Size: 5mm x 10mm

Often gotten with the thing that you are presently reviewing.

Binder Head Screw, M3x8mm, (10Pcs)

These are 3x8mm Binder Head Screws from HPI Racing.
(Penny not consisted of)
FEATURES:
Plain black steel construction.
Binder head with a phillips recess drive insert.
Used for many applications in all HPI cars and trucks

CONSISTS OF:
(10) Screws

SPECIFICATIONS:
Length: 8mm
Size: 3mm

You will like this item if you have the item above stated.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Pack with
the Venom Universal Plug System.

FEATURES:
Wired for stabilizing
Venom Universal Four Plug System enables connection between today's
    4 most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    simply connect wanted plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Pack with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if using
    Duratrax Onyx series
LiPo Balancer such as the Team Checkpoint Pro Vehicle balancer (TCPP9150)

SPECIFICATIONS:
Setup: TWO
Weight: 277g (9.8oz)
Measurements: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Min Discharge Volts Per Pack: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Pack: 8.4V

REMARKS:
CHECK OUT the ENTIRE guideline sheet consisted of with battery before usage
ALWAYS use a LiPo-approved Charger
ALWAYS use a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER allow to Discharge listed below 2.5V per cell
NEVER disassemble or modify pack electrical wiring in any method or leak cells
NEVER place on flammable products or leave ignored throughout
charging
ALWAYS charge in a fire-resistant place
ALWAYS set charger's output volts to match battery volts
CONSTANTLY keep out of reach of children

Want an additional great thing to match the above pointed out thing?

Flanged Lock Nut, M4, (4Pcs), Bullet St/Mt, Rs4, Venture, Sport

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be used for wheels, slipper clutch springs, & other applications
    which require simple elimination and will not loosen up due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECIFICATIONS:
Size: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")

Right here is an additional thing that compliments the thing being reviewed.

2-Speed Set Screw M3x3mm (6)

These are 3x3mm Set Screws by HPI.

FEATURES:
Plain silver metal construction.
Hexagon socket drive insert.

INCLUDES:
(6) Set Screws

SPECIFICATIONS:
Thread: 3mm (0.118")
Length: 3mm (0.118")