HPI Ball Bearing, 5X10x4mm, (2Pcs)

These are 5x10mm Rubber Sealed Ball Bearings for the Proceed by HPI Racing.

FEATURES:
Replacement ball bearings for the HPI 1/8 scale Proceed.
Competition low friction ball bearing.
Bearings are rubber sealed to safeguard against dirt and grime.

INCLUDES:
2 Rubber Sealed Ball Bearings

SPECS:
Size: 5mm x 10mm

Often acquired with the item that you are currently checking out.

Binder Head Screw, M3x8mm, (10Pcs)

These are 3x8mm Binder Head Screws from HPI Racing.
(Cent not included)
INCLUDES:
Plain black steel construction.
Binder head with a phillips recess drive insert.
Used for many applications in all HPI vehicles and trucks

CONSISTS OF:
(10) Screws

SPECS:
Length: 8mm
Size: 3mm

You will certainly enjoy this thing if you have the thing previously stated.



This is the Venom 7.4V 5000mAh 40C Hardcase LiPo Battery Load with
the Venom Universal Plug System.

FEATURES:
Wired for balancing
Venom Universal Four Plug System enables connection in between today's
    4 most common battery plugs, Tamiya, Traxxas, Deans and EC3,
    merely connect desired plug to Venom plug on battery's wire leads

CONSISTS OF:
7.4V 5000mAh 40C Hardcase LiPo Battery Load with Tamiya, Traxxas,
    Deans and EC3 Plugs

NEEDS:
LiPo capable charger such as the DuraTrax Onyx series
Charge Lead Banana Plugs with Deans Ultra Male (DTXC2221) if utilizing
    Duratrax Onyx series
LiPo Balancer such as the Group Checkpoint Pro Car balancer (TCPP9150)

SPECS:
Configuration: 2S
Weight: 277g (9.8oz)
Dimensions: 25 x 46.5 x 137.5mm (0.98" x 1.8" x 5.4")
Charge Rate: 3C (15A)
Continuous Discharge 40C (200A)
Min Discharge Volts Per Load: 6.0V
Max Burst Rate: 80C (400A)
Max Volts Per Cell: 4.2V
Max Volts Per Load: 8.4V

COMMENTS:
CHECK OUT the ENTIRE direction sheet included with battery prior to use
ALWAYS utilize a LiPo-approved Battery charger
ALWAYS utilize a LiPo Cell Balancer
NEVER Charge over 4.2V per cell
NEVER Charge at currents higher than 1C
NEVER Charge through the "To ESC or "RELEASE" lead
NEVER Trickle Charge
NEVER permit to Release below 2.5V per cell
NEVER disassemble or customize pack circuitry in any method or puncture cells
NEVER put on combustible materials or leave unattended during
charging
ALWAYS charge in a fireproof place
ALWAYS set charger's output volts to match battery volts
ALWAYS stay out of reach of kids

Want another fantastic item to match the above discussed item?

Flange Locknut M4 (4)

These are 4mm Flanged Lock Nuts from HPI Racing.

FEATURES:
Plain black steel construction.
Nylon inserts.
Can be utilized for wheels, slipper clutch springs, & other applications
    which need easy removal and will not loosen due to vibrations.

INCLUDES:
(4) Flanged Locking Nuts

SPECS:
Size: 9.6mm (.38")
Thread Size: 4mm
Height: 5.7mm (.23")

Below is another item that praises the item being gone over.

2-Speed Set Screw M3x3mm (6)

These are 3x3mm Set Screws by HPI.

FEATURES:
Plain silver metal construction.
Hexagon socket drive insert.

INCLUDES:
(6) Set Screws

SPECS:
Thread: 3mm (0.118")
Length: 3mm (0.118")