Hot Racing Composite Gear Case With Aluminum Motor Plate

This is the Hot Racing Composite Gear Case with Aluminum Motor Plate
for the Traxxas 1/10 Bandit, Rustler, 2WD Stampede, and 2WD Slash.

FEATURES:
Light weight carbon fiber composite transmission case
Longer motor installing slots for more gear ratio combinations
CNC 6061 aluminum motor plate, heat sink and arm install
Bigger open area for a bigger motor heat sink
Thirty day minimal service warranty beginning at date of purchase-valid
    in the United States only

CONSISTS OF:
Transmission Case with Heat Sink Motor Plate and Arm Mount

Below is another product that praises the product being gone over.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Want another fantastic product to compliment the above stated product?

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing building and construction
Blue rubber dirt guards

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside size: 3/16" (5mm)
Outside size: 7/16" (11mm)
Width: 5/32" (4mm)

Frequently acquired with the product that you are currently checking out.

Sealed Aluminum Differential Case For Traxxas 2Wd Electric

This is the optional Hot-Racing Aluminum Differential Case
for the Traxxas Bandit, Rustler, 2WD Stampede, 2WD Slash
and Monster Jam Automobiles

FEATURES:
CNC aluminum building and construction diff case, black in color
Solidified steel gear
Sealed differentials allows tuning to track conditions by altering
    weight of diff oil
4 O-rings assist seal versus fluid leakage
Thirty day minimal service warranty beginning at date of purchase- legitimate
    in the United States only

CONSISTS OF:
Sealed Differential Case
4 O-Rings
2 Screws

SPECIFICATIONS:
Outside Size: 1.48" (37.5mm)
Shaft Size: .200" (5.10mm)
Total Density: 0834" (21.2mm)

Get this product to enhance the one you are reading about.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel building and construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL version of the Rustler
or Stampede.

Get this product to enhance the one you are reading about.

Slash Big Bore Shocks

This is the optional Huge Bore Shock Set for the
2WD Traxxas Slash.
These replace the plastic shocks that come stock with the kit.

FEATURES:
Strong aluminum building and construction, coated
Anodized black with white springs
Totally assembled

CONSISTS OF:
4 completely assembled shocks with white springs
Mounting hardware
One bottle of silicone oil

REQUIRES:
Filling shocks with shock oil and assembling onto the model

The below product also sets truly well with the product being gone over.

Planet Gears & Shafts

These are the replacement planetary gear and shafts for the Rad 2 and Hawk 2.

FEATURES:
All these gears and shafts are made of metal(probably with a low
quantity of steel).

CONSISTS OF:
4- planetary gears
4- planteary gear shafts
2- sun gears
1- sun gear alignment shaft

WAJ
1/16/94