Hot Racing Composite Gear Case With Aluminum Motor Plate

This is the Hot Racing Composite Gear Case with Aluminum Motor Plate
for the Traxxas 1/10 Bandit, Rustler, 2WD Stampede, and 2WD Slash.

FEATURES:
Light weight carbon fiber composite transmission case
Longer motor mounting slots for more gear ratio combinations
CNC 6061 aluminum motor plate, heat sink and arm install
Larger open location for a bigger motor heat sink
Thirty day restricted guarantee beginning at date of purchase-valid
    in the United States just

CONSISTS OF:
Transmission Case with Heat Sink Motor Plate and Arm Mount

Here is one more item that praises the item being gone over.

Teflon Washers 5 X 8Mm (20)

These are Replacement Washers from Traxxas.

FEATURES:
Black plastic construction.
Used on the axles and in the transmission.

INCLUDES:
(20) Washers

SPECIFICATIONS:
Size: 5x8mm
Density: 0.5mm

Want one more wonderful item to compliment the above stated item?

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

CONSISTS OF:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outside diameter: 7/16" (11mm)
Width: 5/32" (4mm)

Often purchased with the item that you are currently reading about.

Sealed Aluminum Differential Case For Traxxas 2Wd Electric

This is the optional Hot-Racing Aluminum Differential Case
for the Traxxas Bandit, Rustler, 2WD Stampede, 2WD Slash
and Beast Jam Vehicles

FUNCTIONS:
CNC aluminum construction diff case, black in color
Solidified steel gear
Sealed differentials permits tuning to track conditions by altering
    weight of diff oil
Four O-rings help seal against fluid leakage
Thirty day restricted guarantee beginning at date of purchase- valid
    in the United States just

CONSISTS OF:
Sealed Differential Case
Four O-Rings
2 Screws

SPECIFICATIONS:
Outside Size: 1.48" (37.5mm)
Shaft Size: .200" (5.10mm)
Overall Density: 0834" (21.2mm)

Get this item to improve the one you read around.

Shaft Slipper Clutch

This is a Slipper Clutch Shaft for the Traxxas Rustler XL
and Stampede XL.

FEATURES:
Steel construction
_
Roll pin pre-installed

CONSISTS OF:
One slipper clutch set

SPECIFICATIONS:
Length: 1.98" (50mm)
Size: .21" ( 5mm)

REMARKS:
This part will fit both the standard and XL variation of the Rustler
or Stampede.

Get this item to improve the one you read around.

Slash Big Bore Shocks

This is the optional Big Bore Shock Set for the
2WD Traxxas Slash.
These change the plastic shocks that come stock with the kit.

FEATURES:
Strong aluminum construction, covered
Anodized black with white springs
Entirely assembled

CONSISTS OF:
Four fully assembled shocks with white springs
Installing hardware
One bottle of silicone oil

REQUIRES:
Filling shocks with shock oil and putting together onto the design

The listed below item additionally pairs really well with the item being gone over.

Planet Gears & Shafts

These are the replacement planetary gear and shafts for the Rad 2 and Hawk 2.

FUNCTIONS:
All these gears and shafts are made of metal(most likely with a low
amount of steel).

CONSISTS OF:
4- planetary gears
4- planteary gear shafts
2- sun gears
1- sun gear alignment shaft

WAJ
1/16/94