Hot Racing 9.5G Brass Kmc Machete Wheel Weights, For Axial Scx24

9.5g Brass KMC Machete Wheel Weights, for Axial SCX24

Hot Racing front or rear wheel weights for the stock 1.0in KMC Machete wheels on the Axial SCX24.

Features:

CNC machined solid brass billet

9g each fitted to the wheels to decrease the automobiles center of mass, increase its stability, enhance climbing up, decrease the possibility for flipping backwards, and make for a total more capable spider|spider}

Friction fit to within KMC Machete wheels. Some CA glue can be utilized to protect installation

Can be utilized either in front of back, but if you're only getting one set we recommend using them in the front

Requirements:

Hub: 12mm hex

For : AXI31615

Diameter of outer : 21.4mm

Diameter of within : 12mm

Weight: 9.5g/ea

Width: 8mm

Regularly purchased with the item that you are presently reviewing.

9G Brass Differential Cover, For Axial Scx24

9g Brass Differential Cover, for Axial SCX24

Hot Racing heavy brass cover for SCX24 Worm gear Axles Adds 9g of weight to the axle in a low and central location to decrease the automobile's center of gravity, increase its stability, and make it an overall more capable crawler.

Features:

CNC machined solid brass billet

Adds 9g of low and central weight to lower and centralize the automobile's center of mass, increase its stability, and make it an

Overall more capable crawler

mm increased density over stock cover for extra strength and weight

Fits either the front or back

Requirements:

Width:14.33 mm

Height:24 mm

Weight: 9g

Want an additional great item to match the above discussed item?

Brass Front Steering Knuckle, For Axial Scx24

Brass Front Guiding Knuckle, for Axial SCX24

Hot Racing heavy duty brass SCX24 Worm gear Axles guiding knuckles (guiding blocks) for the Axial SCX24 axles. Add weight to your spider where it needs it - down low.

Features:

CNC machined solid brass

Heavy to add weight to automobile for greater stability and lower CG

Cutouts on knuckle for access to outer bearing race for simple bearing elimination

Direct replacement for factory plastic guiding knuckles

Want an additional great item to match the above discussed item?

Brass Stock Wheels Hub, 7Mm Hex, For Scx24

Brass Stock Wheels Hub, 7mm Hex, for SCX24

Features:

CNC Machined Strong Brass construction.

You Will Get:

Four Hex Wheel Hubs

Four 2 x 6mm Axle Pins

Requirements:

Assembly onto SCX24.

Specs:

Hex: 7mm

Inner diameter: 4mm

Below is a great item that many others have actually purchased the very same time.

Aluminum Front Bumper W/Fairlead And Light Buckets, For Axial Sc

Aluminum Front Bumper w/Fairlead and Light Buckets, for Axial SCX24

Hot Racing CNC machined aluminum front bumper with 3mm LED light containers, winch fairlead for usage with Axial SCX 24.

Features:

Billet CNC machined aluminum

Anodized a trendy flat black

Integrated brush guards

Light containers for 3mm LED lights

Requirements:

Width: 58mm

Height: 8mm

Below is a great item that many others have actually purchased the very same time.

SCX24 Deadbolt 1/24th Scale Elec 4WD - RTR, Red

Key Features:
• Includes radio system, ESC and transmitter batteries
• Includes motor and on-board LiPo battery
• Sensible narrow-stance rock spider body in olive green or red
• Molded roll cage with sensible light bar
• Sensible driver figure and numerous other scale details
• Officially licensed KMC XD229 Machete Crawl wheels
• Officially licensed Nitto Trail Grappler M/T tires (S30 compound, big block tread)
• Full-time 4WD
• Splined and sleeved front and rear drive shafts allow for optimal suspension travel while keeping the power to the wheels
• Steel front and rear axles, front stub axles and dogbones provide strength and sturdiness
• Rugged steel C-channel frame rails with bracing keep everything rigid and lined up
• Front and rear axles consist of a two-piece, molded plastic solid axle style
• 3-Link front and 4-link rear suspension supply optimum handling
• Coil-over shocks with simulated reservoir and resilient plastic suspension links provide tested Axial crawling performance
• Front and rear differentials each home a worm gear setup to power the axles and create higher ground clearance. Worm gear drive also supplies a low gear ratio to decrease torque twist
• Two LEDs in the front bumper for night driving
The SCX24™ Deadbolt™ 4WD is the very first Axial® off-roader in 1/24 scale. At less than 8” long, it’s the perfect rig to take along on your hiking, camping, and other outside and indoor experiences — offering factory-assembled ease, scale looks, and confident handling on any trail.

Even new modelers driving the SCX24 chassis will be well-equipped to deal with hard climbs up and rough routes. Like the larger SCX10™ chassis, this smaller sized version uses a lot of steel components — from the C-channel frame rails to the front and rear axles and dogbones. Even over off-road, mountainous, rocky and desert surface, it has the strength to keep pushing onward and upward.

For the most dependable handling, the SCX24 chassis includes a three-link front and four-link rear suspension. The mix of coil-over shocks and resilient plastic suspension links delivers Axial-worthy crawling performance even at this small scale. The worm gear drive setup allows a high ground clearance plus a low gear ratio that minimizes torque twist.

Powered by an included 180-size motor and LiPo battery, the SCX24 Deadbolt displays skills and charisma on the routes. Check out that Deadbolt body — with its narrow position, bulging hood, sensible driver figure, and molded roll cage with sensible light bar. The realism continues right down to the ground, where you’ll discover licensed KMC XD229 Machete Crawl wheels wrapped in Nitto Trail Grappler tires.

Adding a lot more to its novice appeal, the SCX24 Deadbolt comes 100% total and all set to run. Everything needed for action is in the box: put together and completed automobile; Axial 2-channel 2.4GHz radio system with servo and ESC/receiver unit; Dynamite® 88T brushed electric motor and 350mAh TWO 7.4V LiPo battery; USB LiPo battery charger; and even 4 AA cells for the transmitter!

What's in package?
(1) SCX24™ Deadbolt™ 1/24 Scale 4WD Truck
    (1) Axial AE-6 ESC/receiver combination (set up)
    (1) Dynamite® 88T brushed electric motor (set up)
    (1) Axial AS-1 guiding servo (set up)
(1) Axial® AX-4 2.4GHz 2-channel radio
(4) AA transmitter batteries
(1) 350mAh TWO 7.4V LiPo battery
(1) USB LiPo battery charger
(1) Product Handbook




STEEL C-CHANNEL CHASSIS FRAME RAILS
Much like the 1/10th scale SCX10™ platform, the SCX24™ chassis features rugged and tough steel c-channel frame rails with bracing to keep everything intact and lined up.
 

DYNAMITE® 88T BRUSHED MOTOR
The Dynamite 88T brushed electric motor supplies the right amount of torque to help ascend high climbs up. It's mated to a steel motor mount to keep flex to a minimum, which assists safeguard the equipments.
 


WORM GEARS
The front and rear differentials each home a worm screw and worm gear setup to get the power to the axles and create higher ground clearance.
 

DURABLE STEEL AXLES
Steel front and rear axles, front stub axles along with steel dogbones provide strength and sturdiness to keep things running throughout hard climbs up and rough routes.
 


SPLINED DRIVE SHAFTS
The front and rear drive shafts are splined and sleeved to allow for optimal suspension travel while keeping the power to the wheels.
 

COILOVER SHOCK ABSORBERS
Even at this small scale, the mix of coilover shocks with simulated reservoirs and resilient plastic suspension links delivers the crawling performance you've known and expect from Axial.
 


FRONT AND REAR SOLID AXLES
The front and rear axles consist of a two piece, molded plastic solid axle style. For optimum handling, the SCX24™ suspension includes a three-link front and four-link rear setup.
 


LED LIGHTS INCLUDED
Two brilliant LED lights are consisted of and are mounted in the front bumper. An additional LED light port on the ESC enables you to add optional LED lights.
 

4-LINK REAR SUSPENSION
The suspension geometry makes use of a 4-Link style for the back which is enhanced to decrease axle guide and torque twist. We've also consisted of extra suspension links for adjusting your wheelbase length.
 


KMC XD229 MACHETE CRAWL WHEELS & NITTO TRAIL GRAPPLER M/T TIRES
Officially licensed KMC XD Machete wheels are famous in the off-road world. They are molded in black and function stunning scale details, regardless of the small scale.
The formally accredited Nitto Trail Grappler M/T Tires use a wonderful mix of off-road performance while still retaining excellent composure for on-road usage.
 

HINGED BODY SYSTEM
The hinged body system provides simple access to on-board components. You can rapidly reach the battery and chassis by removing simply two body clips and swinging the body up.
 


FULL BALL BEARINGS
Just because the SCX24™ is smaller sized in size doesn't suggest the features need to do the same. No bushings discovered here, rather the drivetrain is easily spinning on sealed cartridge bearings throughout the whole automobile.
 

AXIAL AS-1 SERVO
Installed simply above the front axle is the Axial AS-1 servo, with a servo saver that permits guiding accuracy, while also supplying defense for the servo equipments in the event of a bind or effect.
 

Requirements

Type: Crawler
Scale: 1/24
Length: 7.8" (199.5mm)
Width: 3.9" (99.5mm)
Height: 4.73" (120.2mm)
Ground Clearance: 1.06" (27mm)
Wheelbase: 5.25" (133.5mm)
Weight: 0.5lb (0.22kg)
Chassis: Stamped steel rails
Suspension: Strong axle, front and rear
Drivetrain: 4WD
Tire Type: Nitto Trail Grappler M/T, big block tread
Speed Control: AE-6 ESC receiver/combo
Radio: AX-4 2.4GHz 2-channel
Servos: AS-1 steering servo
Batteries: 7.4V 350mAh 30C LiPo (consisted of)
Charger: USB LiPo battery charger (consisted of)
Gear Pitch: 32-Pitch
Wheel Size: 0.48" (12.4mm) width, 1.0" (26mm) diameter
Kit/RTR: RTR
Shock Type: Plastic body coil-over .9 - 1.3" (24 - 33.4mm)
Body: Painted and cut Axial Deadbolt
Ball Bearings: Complete body
Is Assembly Required: No